We are currently working on a project using Enhanced ShockBurst (ESB) and would like to enable Front-End Module (FEM) support with the nRF21540.
According to the Enhanced...
Hi,
Is it possible to make the MQTT connected device receive the Shadow config updates and AT Commands immediately? Based from our testing, the device only receives the...
Hello, I would like to appply change in asset tracker template FROM nrf_cloud to Firebase Realtime Database.
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main...
Hi there, I´m totally new to Zephyr & Nordic, started with some Trainings on NRF52840DK and jumped in with a device driver developement where I took a availalbe out of Tree...
Hi! We are having problems pairing a nRF52840 against linux (ubuntu 25.04). Pairing fails instantly, before any passkey is shown on the host, returning with code 9. Short...
Hi All, I encountered an issue while trying to use both Bluetooth and ESB in the same application. To clarify upfront: I am not using these protocols in parallel. Also, I...
Hi,
1.How should nRF21540 be added to the nRF52840 DK ncp example? Please provide the lines of code that need to be modified. 2. How should the uart interface be modified...
Hi,
Maybe someone can point me into the right direction, I'm on S110 and SDK10 for hardware/legacy reason.
I have a pstorage function using init, load, clear and write...
Hi.
I am investigating the cap touch for a while, and I am working directly with the capacitive driver from here.
As being said there and other places, the driver will...
Hi all
What is the minimum required length of a LOW pulse to be detected by the nRF52832 via GPIO SENSE mechanism? I couldn't find it in the product specification.
I...
Hi Nordic Team,
I am using board PCA10040 wtih nRF52832 SDK 11.
I have Added DFU code to ble_app_hrs_freertos example.
Once I will go for DFU from nrf Mobile Application...
Hi all
I was investigating a NMI_interrupt today and found out that it was caused by a race condition in the fstorage module.
The problem may occur after a flash operation...
HI ,
I am using nrf52832 with s132 . I am trying to measure ADC value at some periodic interval. In nrf_drv_timer_init() function , code gets restarting after executing nrf_timer_event_clear...
Hi,
I use bootloader from SDK6 and I have sd_power_system_off() in on_ble_evt in event BLE_GAP_EVT_TIMEOUT and BLE_GAP_EVT_DISCONNECTED. I use SDK7.1 and SD110 7.1.
It cause...
I'm programming an application that uses the NUS, and I'm trying to test my code using the Android version of nRF Connect. I'm using a nRF52832 on dev board PCA10040, and...
Hello,
With sdk13 and app_pwm library, I only got 9bits resolution for 32KHz freq.
The pwm should have 16bits resolution, with max freq 100KHz?
please could anyone...
hi ,all
I feel confused about" out_of_sync" and" in_sync" parameters .If a devece is in sync,how the channels was changed ?And what's the use of"nrf_gzll_set_device_channel_selection_policy...
we builded " BLE to IR " using nRF51822 , it was working fine with out the softdevice.
problem start when we integrated with the SoftDevice .
1.the problem that we need...
Hi.
I am trying to get a capacitive sensor library using a button ( 2 plates, one to ground, one to the AIN, separated).
It's going crazy, sometimes it just get tones...
hi,
I'm designing a board with nrf51822 chip. this board work on 2450 lithium rechargeable battery and it contain an MCP73831T circuit which is responsible of recharging...
Good Afternoon,
I hope someone can point me in the right direction.
We've customised an NRF51822 beacon and made it into a sensor but there seems to be an strange error...
Hello all , please your help
I need please , a reference design of nRF51822 for minimum with CR2032 .
using a pcb antena . ( distance is 4M) + the JTAG lines ...
