Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
We have these Dev Kit Nrf52 and also Nrf51 Bluetooth Smart Beacon Kit. For our application and for the simplest user experience we would like to benefit from update via OTA...
My product only offer a debug interface（SWDIO/REST，SWDCLK，+3.3v，GND），but I learn that the nRF51 DK debug out interface has several pins，such as EXT VTG，EXT GND DETECT，EXT...
hi all:
I am a new user.Now i have a project in which I need to implement a function a host and four devices .I just want to know if i use the example of " gzp_dynamic_pairing...
Is a delay needed between Characteristic updates
I modified the ble_sdk_app_proximity example.
I added x3 services, based on the BLE Characteristics, a beginner's tutorial...
I have 32-bit float numbers, sent to the BLE from SPI.
I can manipulate this into x4 bytes, or actually use sprintf and get a real 6-byte representation of the number.
...
I have taken ble_app_ancs_c_s130_pca10028 example and modified the application to run on our custom board.
The custom board uses NRF51822 (NRF51 IC revision 3).
The following...
Hi,
We are using nRF51822_QFAB (128K/16K), S110 V8.0.0 and SDK V10.0.0 for my development. We are in the need of guest (unbonded), pairing and bonded mode.
Guest...
Hello,
I'm struggling with setting up the eclipse IDE to build the blincky program in the SDK now I've configured all the paths and eclipse configuration according to this...
Hi ,
I am using nrf5 SDK v12.2.0 ,
I have an nrf51822 board .. can I just compile the examples in SDK for pca10031 and use it for nrf51822 . Please let me know what I...
Is it possible to have two nRF52 devices connected in such a way to send UART data in a bi-directional way.
Would device 1 be a BLE central and the other BLE peripheral...
I followed the link: infocenter.nordicsemi.com/index.jsp to build and load the app into two boards.
Step 1 ~ 8 are working as expected. But
Step 9 "Observe that LED...
Dear Nordic,
What I want to do:
Battery powered sensor network
One gateway (BLE --> WLAN) with a serial-to-wifi chip connected to nRF52
MQTT (IBM Bluemix -...
Hi there,
I'm in the middle of migrating an application from SDK 10 to SDK 11. In the SDK 10 version, I had RTT logging working just fine. I'm developing on a Mac so I...
Hi guys
I am using customized board(Raytac MDBT40) based on nrf51822(flash memory 256k, RAM 32k).
I am trying BLE UART example code of SDK 11.
which path : \nRF5_SDK_11...
