I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Using Segger , only the BLE template is advertising,All other BLE apps such as BLE_UART, will flash the leds very fast but will not show on any Apple device on the Bluetooth...
We have an ISR parsing incoming serial data from the UART. When a valid packet arrives, I'd like to be able to wake the core from whatever low-power state is entered when...
That is probably an old topic, but after doing some research I could figure it out: calling sd_app_evt_wait() on my nRF5832 + nRF5 v11.0.0 SDK + s132 causes my chip to reset...
Hi
I've some troubles with the ble disconnection of S110.
Always when I call the sd_ble_gap_disconnect function after successful connected, the error code 8 NRF_ERROR_INVALID_STATE...
As I can see, I flashed Zephyr to Carbon 96 board, I don't fully understand the process,
I mean, I see .bin and .elf files but i don't see boot.img file, how do i make a...
The nRF52832 datasheet refers to a transmission of multiple packets in Figure 37. I have attempted to load multiple packets to the radio FIFO using nrf_esb_write_payload(...
Hi All,
I have developed an application on the RedBear BLE Nano2, and am trying to port it accross to a custom nRF52 board.
The Hex that the Arduino IDE outputs does...
I have an application which requires protection from passive eavesdropping, but not man in the middle attacks. I want to enforce the use of diffie hellman key exchange.
...
Hello
i am using Nrf52840 with sdk 132 and version 12.2
i am using the Heart Rate example as template.now i am just testing.
Before making connection,i like to Advertise...
I have a sensor which has output in the range of 0-5V. I want to connect it to an nrf51822 GPIO pin and to be able to read the value via it's 10 bit ADC. Is there any guide...
hello, there my application is like that...
(1) calculate size of receive buffer. than read that size of data.
again new data comes, then again calculate that size of...
Issue: With my external antenna design, I get lower dbm than PCB antenna (nRF51DK) with same distance.
My external antenna design: -70dbm
nRF51DK: -40dbm
In this...
Today when I started power profiler kit, it suddenly started to show peak values like 80 mA. This has not happened before, but the values with the same hardware have been...
In the data sheet of the NRF51 and 52 there is mention that sensitivity of NRF51 is -96 dBm and NRF52 -98.
But I read some where that when RSSI is -90 then that signal...
