Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi everyone,
I'm using a custom wrapper ( github.com/.../arduino-BLEPeripheral) with softdevice S130 v2.0.1. I've extended the wrapper to allow simultaneous advertising...
I am trying to implement a simple example with custom profile by building upon
the tutorial given devzone.nordicsemi.com/.../
My profile is something like this:
Service...
Hello,
My application perform reset periodically. When It does a reset the bootloader need to initialize the softdevice with SD_MBR_COMMAND_INIT_SD before calling sd_softdevice_vector_table_base_set...
Good times,
So I finally put in the tweak to enable the GPIO 9&10 pins to be used for GPIO instead of the default NFC mode. Must remember that reset for it to take effect...
Hello,
I'm testing ble_app_hrs example by nRF52832 DK.
When i change NRF_BLE_GATT_MAX_MTU_SIZE up to 158, the example project run properly.
But, when i change MTU...
Hello, I am using nrf52832 custom board, with SDK 11.0.0 and s132_nrf52_2.0.0 and trying to dim led. It seems the only suggested solution is to use the pwm driver. I was wondering...
Hello, im experimenting around with the nRF52 DK (and nRF51 DK also)
Now I have following setup on nRF52 DK:
SoftDevice: s132 nRF52 v2.0.1
Applicatoin: Example Project...
I have the option to connect nBLE51822 to MCU via SPI, UART or I2C. But is there any advantage of using SPI/ I2C interface over UART interface while connecting nBLE51822 to...
my code is below.
git_mpu9250_dmp.zip
Hello.
I use nRF52 & MPU9250.
I want to use DMP,
but I can't read data with DMP.
Because it have failed that writting firmware...
Hi there,
What is the recommended development tool setup for nRF52 Preview DK on Mac OSX?
Your guide for SDK 0.9.1 seem to rely on Keil which isn't natively available...
Hi all,
What is the difference between the app_mailbox and the nrf_queue api?
The documentation says:
A)
The mailbox library provides functions to safely exchange...
Hi team ,
I'm using sdk 12.1.0(E:\testing\examples\ble_central\ble_app_hrs_c\pca10028\s130) example.I want to change to this BLE_GAP_ADV_TYPE_ADV_NONCONN_IND in above example...
I'm using nRF52 + SDK11.0.0 + s132. I have a custom service (with a read characteristic and a separate notify characteristic). After adding the DFU service and uploading the...
Hi,
Following the docs I think I am able to write to flash but it will not read anything .
This is how I set it up, write and read :
static void sys_evt_dispatch(uint32_t...
