Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
As we known we can set static passkey in peripheral side (s110) with the API sd_ble_opt_set(BLE_GAP_OPT_PASSKEY, &ble_opt) as below:
inline void setPassKey(void)
{
uint8_t...
I've tried all 4 versions of the HID Mouse Example provided through the Keil Pack Installer tool and can't seem to get any of them working.
The code compiles and downloads...
I was trying to compile the example code(nRF51 SDK8.0) for ANT and flash to my nRF51DK(pca10028) board, but the example code was not working on my board. I tried compiling...
Hello.
I'm now writing a software based on nrf51_sdk_v6_1_0/nrf51822/Board/nrf6310/s110/ble_app_hrs. The SoftDevice I'm using is s110_nrf51822_7.1.0_softdevice.hex. Why...
So I've been using a user submitted SD safe TWI implementation that I found here. This has worked well so far, but upon updating to SDK 8.0.0 parts have broken. Now when I...
Hi,
I'm using the NRF51DK which comes with the nFR51422. I initially flashed the board using the ble_uart example.
Since then I've tried flashing it with other examples...
Since we have some performance problems with sd110 V7.0.0, we tried a upgrade to v8.0.0.
This version(8.0.0) with IC revision 3 solved our performance problems:).
But a...
Hi,
I am working on a project regarding a portable device for healthcare monitoring. This device will have a nrf8001 module integrated that will communicate with a iOS...
Hello there,
I know that the range of the possible BLE communication depends on the internal configuration as well as on the external environmental conditions.
I would...
I downloaded the zip file from Git Hub Nordic.. and extracted it into C:\Keil_v5\ARM\Pack\NordicSemiconductor\nRF_Examples\7.1.0\ble_peripheral\
When I open the project...
Hi~
I have a nrf51822 EK board(PCA10001 V2.2.0), but the J-link OB can't flash 51822 chip.
The situation is:
1.I can see Segger J-link on segger software&nrfgo studio...
Hi all,
I've been trying to get a new Win 7 (x64) PC setup with with the Nordic dev tools.
Studio, MCP, SDK etc.
I've installed Studio (1.17.1) and MCP (3.7.1). This...
Hi...
i have downloaded latest SDK zip file "nRF51_SDK_7.2.0_cf547b5.zip" from developer.nordicsemi.com/.../ but i could find mdk file "nRF51_mdk_6_1_0_installer" only...
Hello,
is there any information about how the acceleration of an IC effects the lifetime? I use the NRF51822 in an environment with around 400 g accelerations.
Greetings...
Not tech support as such but thought it worth asking here...
Does anyone know a good source for nrf24lu1+ dongles ? Since full design/production files are available (nRF2728...
