Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Could Nordic please confirm that the "SB13-SB15" and "SB23-SB25" silkscreen markings incorrectly imply that pin 1 of the SPI flash part, which is actually "!CS" would appear...
I have a custom PCB with an nrf51422 powered by a coin cell battery. The EE who designed the board assured me that the battery voltage could be measured internally through...
Hi community
In order to discovery the server, I have read some examples and I got some questions regarding the use of the following methods:
sd_ble_gattc_primary_services_discover...
Hi,
Is it possible to add additional antenna on the beacon ( NRF51) in order to increase the range ?
If yes kindly let me know the list of available or recommended antenna...
Hello,
I'm currently designing a board with nRF52840 and I'd like to use an antenna that is a DC short to ground. Do I need a DC blocking capacitor in such configuration...
Hello,
I am developing a profile which includes 39 characteristics spread over 4 services on nRF52840/SD140/SDK13. When I add one too many, sd_ble_gatts_characteristic_add...
Hi community,
I'm working on a BLE gamepad with custom board based on 51802 and s130, code modified from ble_app_hids_keyboard . The gamepad works like a charm on my Android...
Hi, Nordic!
We have two PDK-NRF52840 and custom boards with NRF52840 chips.
2 from 5 chips have a broken bit in RAM. This is different places.
For example:
Is this...
Hi all,
if i buy 2 nrf52840dk:
Is possible create an audio connection like intercom between the two dk?
Can I send my voice from "dev board 1" to "dev board 2"?! and...
Hi,
I beginning now to program nrf51822. I would like to let the nrf51822 wake up after 3 hours by using a software timer interrupt.
Should I use power_manage()? Before...
Hi,
I'm trying to configure custom local GATT server on nRF8001 device. I added a custom service with multiple characteristics, but I can't generate source files. It says...
Hello!
I'm doing master thesis and I've chosen WT51822-S4AT board for BLE. I've made board successfully and programmed uC to send serial data to BLE.
I'm able to received...
Hi all,
I am using nRF52832 DK for my project. I need to config BLE for connecting with my phone. After a lot searching, I know that I can use softdevice API for configuring...
I mashed up RTC and SAADC examples. The files of the project are attached in the end of the post. The problem is that after the first iteration (I want to sample audio for...
