FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
I want to use AES ECB block present on nrf51 and nrf52 boards for resolvable private address (RPA) generation.
Are there any measurements about how much battery the...
I have an iot/coap environment setup and i want to read input voltage connected to p0.01.I can read the input in terms of resolution(0-1023).I can convert this values to voltage...
I have a project where I need both TWI instances as well as an SPI instance to be used with sdcard and fatfs libraries. When I try to compile I get the error: SPI1_TWI1_IRQHandler...
hi,everyone,I want to ask who know why sdk11.0 ble_ancs push message without push App Identifier?I look at the print, push the news started with tittle ,and the "p_attr -...
Hi!
I'm trying to use a custom made whitelist with my scanning device, but no data is arriving.
Is there something I need to do at the advertising devices? Here is the...
Hi, I have a custom board based around the nRF51822 which I programmed via SWD with the ble_app_hrs_pca10028_s130.hex image provided in the SDK, however when checking with...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
Hello everbody,
I made some current measurements with mit DK nRF52 and the nRF52832 Chip.
Everythings works fine, but I always get "peaks", as you can see on the Picture...
I am using nRF52 pca10400 and I would sample some audio signal for short periods of time, but I found a lot of difficulties with the SAADC example from sdk 13, since if I...
Hi,
I want to collect sensor-data, save it to flash and access it later.
I´m not quite familiar with ways to save data and get a little bit confused by the fds library...
Hi,
We are currently facing this issue, where after a DFU application firmware update (or bootloader update) the bonding information gets wiped out.
We are using a custom...
Hi,
I'm trying to control LSM6DS3 by TWI communication.
Slave address of the chip is 0xD4 when SDO/SA0 pin is low.
I'm using SDK13.0.0.
My code is like below.
...
I will test the receiver blocking of ETSI with the nRF51822 module
(EN300328 V2.1.1 2016-11 5.4.11 Receiver Blocking).
However, please tell me the next items because I do...
I'm testing the setup for the Receiver Blocking test ask part of EN 300 328 V2.1.1 and I have a question after reading these posts devzone.nordicsemi.com/.../ , devzone.nordicsemi...
