Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
sd_flash_write(((uint32_t *)storage_addr),
(uint32_t *)p_data_addr,
size / sizeof(uint32_t));
why here size value is divided by sizeof(uint32_t).
what is byte value...
Hi,
I'm trying to adapt the HRS/RSCS relay example from the SDK to use the Nordic UART service instead. Currently I can connect to the central just fine, but if I try to...
I'm using RTX timers on NRF51 and I'm getting a 7ms per second error. (I.e. osDelay(1000) takes 1007ms).
It appears that NRF_RTC1 is configured incorrectly in SDK examples...
Hello, I am working on NRF52 customer board + SDK_13.0.0_04a0bfd
I start with ble_app_uart example, I use interrupt tigger a repeat timer(500Hz, 400 times) to sample 6 channels...
I'm having major troubles with my debugging setup using a nRF51 DK (PCA10028 V1.2.0).
When I try to connect to the board I want to debug/program (which has an BlueMod ...
Hi Everyone,
I'm currently busy going through the OpenThread API and examples to better understand what all the functions do. However, I don't fully understand where the...
Preferences: nRF52832 chip, s132_nrf52_4.0.2_softdevice
Two or more nRF52832 chip are connected to iOS and Android.
And do bluetooth off in smart phone.
this case, bluetooth...
This suggests it should be possible to change the beacon advertising content in response to events such as a GPIO input.
I'm using nrf52 DK running the beacon example (SDK...
Hi,
What should I add to the makefiles to be able to generate an assembly code? Something similar to what is seen in the debug mode of Eclipse. I have tried -S/s but it...
Hi
I want to porting to nRF52840 but since S140 SoftDevice Specification documentation doesn't exist
I can not proceed with porintg.
I need S140's detail memory map...
I am using s132_nrf52_3.0.0_softdevice.hex and sdk12 and compiling with arm-none-eabi-gcc. The problem is that the bluetooth set up just jams at:
// Enable BLE stack.
...
I'm trying to get my nRF52 BLE peripheral to connect to my phone while its screen is off and it's in sleep mode. Other consumer BLE peripherals that I have can connect to...
Hello
is this possible to reset the timer.
for example i set the timer for 10 Second.
when he reach up to 5 second then i would like to reset the timer.
i found no function...
Hi,
I just noticed that my PTX and PRX projects use different assemblers and linkers -- not sure why. I got the sample projects from Nordic. What's the difference between...
