Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi there,
I've tried using PCA10040 with NRF Connect to do Secure DFU but no luck. Any idea on how to get it recognized, please?
I'm following this:
infocenter.nordicsemi...
In the Bluetooth Light Controller example for the client, in provisioner.c this beautiful comment can be found:
/* Provisioning encryption key storage (this is not how...
Hi all,
Here is my first question on this forum after many hours working with the NRF but for the first time I didn't found the answer :)
My problem is :
I would like...
Hi,
We have custom board with STM32F407 as an application chip and BL652-SC-01 as a connectivity chip. When we worked on SDK 13 and softdevice 4.0.2 or 4.0.4 we had problem...
Hi, I have problem with using printf() in SEGGER RTT.
I've read tutorial and others about SEGGER RTT printf() problem, but they didn't work.
When I use printf() in RTT...
hi,
I found ble_app_multilink_central example under SDK but this is for LED button application.
Is it possible to configure the same example for NUS?
I worrying about...
I have app (based on buttonless_dfu) works on sdk 13, sd 3, nrf52832.
Now I try to migrate this app to newest SDK14, sd 5.
I can't resolve one issue. I have main.c and 7...
hi, I found ble_app_multilink_central example under SDK ,and make it work with NUS. Some problems bothered me.
When the amount of data reaches a certain amount, the transfer...
Hi,
Tried this getting started tutorial:
github.com/.../Nordic_SDK_User_Guide.md
When building project at the end, I get: (After trying max optimization)
linking...
Hi,
I am trying to program a custom board with ISP1507 chip from dynastream based on nRF52832 using the nRF52 DK. I have connected P20 on the DK to the chip as follows...
Hello, myCode: https://goo.gl/ggTei4 & Photo : https://goo.gl/Sq28tC
Please Help me with Dynamic NRF24L01 Mesh network
I have connected nodes via DHCP 01, 02 upto 05 to...
Hello everyone!
Do have any different between Read/Write internal flash with softdevice and non softdevice!
And how can I get example Read/Write internal flash with softdevice...
using the sample code at
invent.module143.com/.../
i am able to use nrf24l01 to communicate raspberry pi with arduino, but the problem is the timing. I found it takes...
Did anyone attempt time of flight measurements with the nrf52 yet? I'm looking into this as a possibility to measure distances. I was thinking that using the 64 MHz clock...
I AM GENERATING A PWM EXTERNALLY (OUTPUT FROM A WATER SENSOR) AND FEED IT TO A NRF51422 BOARD. I WANT TO COUNT THE PULSE COUNT(LOW TO HIGH TRANSITIONS ONLY). CAN I DO IT WITH...
