Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
Hi
I noticed one ticket says that "the following combination offers low power consumtion and high througput when needed :Short Connection Interval + High Slave Latency ...
I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
Hello!
I want to develop a Heartrate Monitor Device which uses BLE and ANT+ using the Seeed XIAO nRF52840 Plus Board.
Now that I have the board I found out that ANT doesn...
Hi
I have one nordic nRF54L15 DK using as peripheral, I want to know the power of it. Thus, I use PPK2 to be a 1.8 voltage source and connect VOUT to P6 pin 1 and GND to...
How do I produce a signed file to flash to the network core for firmware update? I am using a child image/parent concept with the \nrf\samples\ipc\ipc_service\ project, When...
Hello , I would like to know lifetime expectancy of NRF52832 IC. By lifetime expectancy I mean the amount of duration before NRF52832 goes non-functional. Please help me in...
Hi,
In disk_uninitialize function there are following lines of code:
if (m_drives[drv].last_result == NRF_BLOCK_DEV_RESULT_SUCCESS) { m_drives[drv].state |= STA_NOINIT;...
I have extend the light switch example to send message to the other node. I have refer This example to send message. But how to configure another node to receive the message...
HTU21D.rar hello there i am interfacing HTU21D with nrf51822. i am reading temperature and humidty from HTU21D. humidty register is E5. and temperature register is E3. now...
Hi,
I was trying to implement software UART for our product so I decided to use timer compare channels event connected to gpiote with interrupt. I want to toggle data line...
Hi,
Application: turning on/off a LED by toggling a GPIO pin using a timer and PPI. Important: the on-time of the LED must be very precise, i.e. the jitter must be minimal...
Dear Sir/Madam,
I have a sensor prototype board using nRF51822 for Bluetooth communication and I am now working on its firmware. I have installed MDK version 5.16 and...
Dear sir,
Sir i am using MDBT42V module. I want to know that whether the SCL & SDA pine are internally pulled high in this module ?
Regards,
Manoj Hiwarkar
Hi,
I have a problem where I am getting NRF_ERROR_RESOURCES errors 2 out of 3 times when sending notifications from my peripheral to my central. I think this is caused because...
I have designed a custom board with a TF325J32K7680 32KHz clock with +-50ppm tolerance, for the 32MHz I am using the CX2016DB32000D0WZRC1 with +-40ppm tolerance.
Simple...
Hi,
Within each example in the NRF5 SDK there are a number of folders including
arm4
arm5_no_packs
armgcc
config
iar
I'm having trouble finding an explanation...
Hello everybody,
I used SDK14.2.0 , S132 .
I keep the data from nus_data in the uint8_t array. Then I am trying to write the array with use fds_write.
My fds_write...
Hi, I would like to add source files to Projects with a reltive path. The reason being that I would like to have my own code in a cloud based directory and code from SDK in...
Dear friend,
To u se the Power Monitor for current profile measurement of nRF52832, I prepare the board by doing both of the steps described below:
(1) Short solder bridge...
Hi There,
I currently using PCA10040 development kit for my project. I tried to merge with \nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_blinky\pca10040\s132...
