Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Hi,
I have a Serialization connection working between a Nordic nRF52 CPU (slave) and an NXP CPU (master), using SPI.
The NXP is starting/stopping a BLE Scan on the Nordic...
Hi, I have some questions about the memory map, ram usuage and linker config for the secure bootloader when used with the S332 (4.05 sd_req 0x94) softdevice. I have tried...
USB Virtual COM
Until now, the development has been done by sending the commands via a USB virtual COM. The received buffer of int is processed and sent to the function...
I have an nrf52832 connected to a UART-USB driver with RTS/CTS. CLI manages the UART connection. Using SDK 14.0.
When HWFC is enabled, if a serial connection is NOT established...
Hi, p0.06 is always high lever when the following codes are executed:
nrf_gpio_cfg_output(6); nrf_gpio_pin_clear(6);
Why?
Softdevice is used in the project.
I have searched through the examples and the documentation (BTW the online document links are broken - the offline documentation is nice however).
From what I can tell...
Hello Everyone.
I am doing a project where I need to do a Bluetooth communication of data. I have two nRF51 DK so the idea is to connect a particular pressure sensor to...
I am trying to create a state machine that will be able to turn the Bluetooth radio on/off and possibly change the mode of the BLE service for power testing. I hope to run...
I have created an instance of time using the standard time function in C. I have also linked it to a counter on a timer so I can track how long the device has been active...
At CES this year (2018) there was a booth showing essentially a roughly 1/4 size Thingy:52. It wasn't actually at the Nordic booth so I'm not sure if it was actually a Nordic...
I think there's a problem with the beacon advertisement sent by Thingy52. I'm seeing the problem in my own PC code and also air sniffer. The advertising data packet looks...
I am using nrf_fstorage_read command to read data from flash. I have defined my start address as 0x68000 and end address as 0x72000.
I erase the memory through nRFgo studio...
Hello,
I've searched around the forum and followed all the advice given in other threads but am still not having any luck.
I've tried running the nRF sniffer on both a...
Hi there. I just got the nRF52840 DK and am trying to get going with it. I have been looking at this getting started page:
https://www.nordicsemi.com/eng/Products/Getting...
Dear lovely people!
Setup: sdk14 / s132 v5 / nrf52832
Just like with the previous SDKs, I tried to make a multilink nus central fw.
The periph device runs my code based...
