Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi
I have a sample nrf51822 non BLE program (based on flashwrite_example) that successfully writes and reads flash (last flash page) in a loop, incrementing the number that...
Regarding DFU upgrade, I have the following questions（sdk14.2）: 1.nrf52832 will be paired and bound after connecting with the mobile phone, then in the sdk_config.h file NRF_DFU_BLE_BUTTONLESS_SUPPORTS_BONDS...
Hi,
I'm working on customized light switch demo where I'm able to send string data over mesh, I'm using mesh SDK v2.0.1, I would like to have Provisioner node to be also...
Hi,
If I connect supply from laptop using micro USB cable, battery on PDK also gets discharged?
Asking this because in the initial stages of testing PDK battery is working...
Hello, I use nRF52840_SDK_Mesh, when I run the Light_Switch example with the first Client for the first nRF52840 card the 4 leds light up, and it's the same with the Server...
I need add the proxy feature to the pb-remote provisioner. I use pb_remote client example. I have added the proxy feature, it works, but when startes advertising (mesh_adv_start...
Hi, I have decided to use Nordic Ble Mesh SDK instead of old mesh example. but I have only got NRF51 DK Boards. It was configured in order to use with NRF52 boards.
How can...
Hi @ll, I'm using Mesh SDK 2.0.0 with SD 6.0.0. The example everything is based on is the dfu-example (including parts of the beaconing example) I'm now trying to add a connectable...
Dear Nordic Team,
I have practiced the " ble-characteristics-a-beginners-tutorial" on DK board PCA10028, and it worked perfectly. Then I tried to change the user defined...
Continuing to port MESH into an IAR project. We would like to make logging work with IAR. Right now, we get a warning that the "format" attribute isn't supported.
Is there...
The valid master out time for <= 8 MHz is shown as tSPIM,VMO 59 ns. The valid master out time for > 8 MHz is shown as tSPIM,VMO,HS 8 ns. The latter tSPIM,VMO,HS could only...
In simple on/off example, the client can turn on several server nodes in the same group in the same time,
but in serial example mix simple on/off server, the info center...
/* Copyright (c) 2014 Nordic Semiconductor. All Rights Reserved. * * The information contained herein is property of Nordic Semiconductor ASA. * Terms and conditions of usage...
Hi there,
I aam using SDK 14 and using all sectors of FStorage. I am using all the sectors of FStorage to read and write data.
After about 24 hours, I see data corruption...
