I'm working on an Android app that connects to a Nordic nRF52833 BLE peripheral (Zephyr 3.7.99 / NCS 2.9.0). I'm encountering a consistent issue where:
The app connects...
I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hi,
To decrease the load on the system I would like to periodically send some BT data (and do some SD card writing).
Since Timer 0 is used by the soft device, I am using...
I want an amplifier to receive audio from a FM/DAB receiver and from an NRF52832 that - in turn - has received audio over BLE. The amplifier should either receive the radio...
when I start to program nRF52832 under 1.8v some memory pages can't be accessed. this is short listing:
Erasing page at address 0x78000. Erasing page at address 0x79000...
Hello,
I'm trying to make some current measurement using the nRF6707 and a nRF5 SDK Board(10040) (Board out of the box, shunts untouched).
We're facing problems measuring...
Hello,
Does the newest SoftDevice release v5.1.0 support the advertising data length extension (255 bytes)? If not, will it be available this year?
We are at the evaluation...
Hi,
I am using nRF52832 DK (PCA10040) SDK 14.2.0 and S132 V5.1.0.
I am planning to test the TWI loopback (in order to familiarise the APIs used for TWI in nRF52).
I...
Hello,
I want to update the connection parameters once the nrf52x (peripheral) is connected with the android (master). I tried the following:
In connection event i called...
Hi, Nordic.
I want to use BLE buttonless DFU sample application.
I tried to compile it using SEGGER Studio + clang, but compile error occurs as the below.
How can...
Hello, Everyone.
I have face some major issues.
First i explain the set-up of my project.
-> I have nrf51822 chip and connected to the external flash memory.
->...
Hi there,
I was trying to understand "sleep" power modes of the chip (CPU + Peripherals) in a bit more details - but my understanding is that everything is handled by the...
Hello guys,
these days i started to work with the CryptoCell library on nrf52840 and i'm facing some issues running AES CCM* mode
little example with pseudo code for initialization...
Hi there,
A little background in my experiences first: I've programmed a couple PIC24 microcontrollers in the past for VERY simple embedded system projects (i.e. making...
hi:
I am working with the nrf52832, and the radio transmitting data packet.I find the receive data is ok, but the crc indicate a data error. Why? This problem is same with...
Hey!
I'm working on a device which requires Bluetooth to be completely disabled for short periods of time. It's got a sensor in it that's sensitive to 2.4 GHz radiation...
Hello Nordic Guys,
We are working on the system based on BLE_APP_UART_C (central) and BLE_APP_UART (peripheral).
“Central” is always “ON” and scanning for the peripherals...
