Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Dear friend,
To u se the Power Monitor for current profile measurement of nRF52832, I prepare the board by doing both of the steps described below:
(1) Short solder bridge...
Hi There,
I currently using PCA10040 development kit for my project. I tried to merge with \nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_blinky\pca10040\s132...
Hi
We have a product with Nordic nRF9E5 coupled to Texas CC1190 amplifier.
We are seeing transients at start and end of TX; worst at end. We appear to be non-compliant...
Hello, we are using SDK 5.2.0, SoftDevice 6.2.1 S110 on the peripheral side and S130 on the central side.
We have implemented a serial data link between the two, the central...
I have made a custom PCB with the nRF52832, following the circuit reference, I used the C3 and L1 for tunning the antenna. Instead of a chip antenna I placed a wire in the...
The NRF_LOG library apparently uses memobj, which uses balloc. I assume that means I need to add some blocks in my sdk_config (i.e., MEMORY_MANAGER_SMALL_BLOCK_COUNT, etc...
Hello Guys,
I have some measurements for the determination of the maximum range and the energy consumption. The experiment is based on the ATT_MTU throughput example, nRF5_SDK_14...
Hi,
We have a BLE peripheral device that is used as a mouse/keyboard (nRF52832 SDK 14.0)
The peripheral pairs with most central devices just fine (including Mac and PC...
I have two nrf51 development board. A is PRX, B is PTX. now B can send payload to A , and A can receive and response it by ACK. But some times A want to send payload to B...
hi Nordic support team ,
i have sent my application data to nrf connect .I want to send that data when i write something in "write value " option in nrf connect .After comparing...
Could anybody help me with some useful stuff and links to start programming from scratch for nrf52832 DK on Keil v5. I have some of my undergrad students who need this help...
Hi, guys, I tried nRF5_SDK\examples\ble_peripheral\experimental_ble_app_eddystone example on nRF52832 and it works perfect.
And I compared the code with the normal BLE advertising...
I got this info when I use keil to download progream though jlink.my board is NRF52832,the version of my keil is V5.24 and the version of my SDK is 14.0.
why it's happened...
Using SDK 14.2.0 and PCA10056 Dev kit: when I load the example (usbd_cdc_acm) and flash it, it works well, can communicate in both directions (windows 10 and debian linux...
During more than two years SDK contains OTS in 'experimental' mode. Do you have any plans to update this service (and write an example how to use), or better avoid using this...
