Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi all,
I would like to setup a system where a single central BLE device (a smartphone) has to talk sequentially to several BLE perihperals (Nordic chips).
I need to...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I made timer(repeated) as below.
void init_timer(void)
{
uint32_t err_code;
err_code = app_timer_create(&m_timer_id,
APP_TIMER_MODE_REPEATED...
Hi,
I have a nrf51-DK, and I use softdevice s130_1.0.0 with keil c 5.18a,
My project with custom service uuid "DFU" and custom uuid "my_uuid", and battery uuid, alert...
Hi,
I've noticed that in the examples that come with nRF5 SDK11 there is a template for creating BLE peripherals (ble_app_template). I was wondering if a similar example...
Hi.
I'm using PCA10028, SDK10.0.0, S130 as central.
After connection, if i want to change SUPERVISION_TIMEOUT, is it possible?
If it is, how can i do that?
I need...
Hi.
I am trying to get the RTC started, and I've followed the rtc example in the NRF51_SDK.
But things go wrong when I call:
ret_code_t err_code = nrf_drv_clock_init...
Hello , RX: nrf24LU Tx: nrf51822 use ESB Lib. But the nrf24 Can't receive data continuous.
if I Want receive 2th data , I must power up the nrf24.
This is my Code :
RFCTL...
hello,
I wanted an info which tool is better for debugging when using
native SDK.
do i have to use pyocd or openocd for native sdk hardware debugging
and if you can...
Based SDK 9.0 "ibeacon" example, nRF51822(QFAAG0) work's well when download the ibeacon.hex.
The target set as follow:
Based SDK 9.0 "ibeacon" example,nRF51822(QFABC0...
Anyone seen the new nRF52 online power profiler ?
It's an online tool that estimates the current consumed by your BLE application.
This allows you to better understand...
Hi,
Before starting advertising using advertising_start() function, if pstorage function is used to write data, then it gets stuck at that point as no pstorage handler...
Hello, I have an issue with ble_app_hrs_rscs_relay that doesn't seem to exist with the other sample projects.
The project compiles without any issues, but when I run it...
Apart from pressing Button 4 or adding a DFU service to current running application. Is there any way to enter DFU mode from application?
Is it possible with nrfutil to...
Is there any tutorial or good example for I2C communication using TWI? I already saw the examples for TWI, but I don't find them very intuitive to change for I2C.
I'm trying...
