Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hello,
I am currently working on adding the pairing part to the ble_app_uart with peer manager. I have followed the way that is used for ble_app_gls and ble_app_hrs. I could...
Hi support team,
I download mesh (nrf5_SDK_for_Mesh_v3.2.0) serial example FW to nRF52840 DK,
and connect to embedded linux gateway over USB,
I can run PyACI example...
Hi,
It seems that s112 soft device uses IRQ level 0,1,4 of nRF52832.
By default my counter has default IRQ level 6, my concern is about the delay of COMPARE interrupt...
Hi, Everyone
Environment: SDK15.3, nRF52840, Keil Compiler
I want to keep the previously set values undeleted even after OTA
My question is
1) Which method is better...
from this guide
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader#h23sjziacp7vrw0scs2t3tua1ax0426
It is...
Good evening.....
I am looking to play around with the Thingy 91 but I am a hardware guy who knows enough about firmware to be dangerous. I typically run into issues getting...
Hi,
I am trying to send firmware image from one board to another board. For that I want to use DFU control point characteristics.
I am using nrf52832 development kit...
I have installed the cocoapod for nrfMeshProvision, but i am new to BLE technology. I am able to fetch the dataIn and dataOut characteristics, but stuck at creating a Proxyhandler...
Hi,
I have a project where we want to setup 3 PWM channels for dimming LED strings in a mesh configuration. So the mesh dimming server is a perfect starting point. I did...
Hello,
Our team is new on development nRF52832 firmware.
Now we have an issue on standby current for nRF52832.
We have a 5 second timer for a PWM output.
Sleep (System...
Hello there,
I am facing some difficulties while using nRF52832 NFC for an application.
When I tap the nrf52832 device on the NFC reader the nrf52 cannot able to respond...
Hi, we are currently looking at making a zigbee light switch using the 52811. However since the zboss library files are compiled with FPU directives the only way to build...
I need to read data from sensor and publish it to the mesh network. So the question is do I need to create Sensor model for that or, as in one of your replies , you suggested...
