Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I recently purchased the nRF5340 PDK. I am working through the getting started guide and can't seem to get the Heart Rate Monitor demo application working.
Firstly, when...
trying to get nrfutil working on ubuntu, following this guide:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfutil%2FUG%2Fnrfutil%2Fnrfutil_intro.html
after...
hi, I have used to segger j link basic with nrf connect programmer to program mass production.
but, It takes 30 seconds. For better efficiency, can It be improved to change...
Hi Everyone,
I need to develop a bootloader and a firmware update procedure.
My development environment is nRF52840, sdk 15.3.
Program download configuration 1) Download...
Using Mesh SDK 3.2.0.
The returned Device Composition Data is malformed when requesting it after the node has been reset. This is because the sig_model_count and vendor_model_count...
Hi to all,
i am trying to develop an app with NRF52840 soc and nordic sdk 15.03. in my app i implemented a usb hid device and also i am using flash storage at same time...
Hi
After getting SDK16 , we have tried to load a combined hex file with bootloader + S132 V7 + application with dfu + bootloader setting page to PCA10040. And It work well...
Hi,
i am working with aws-fota example, i copied my certificate to certificate.h file, once i run the program it shows like
The MQTT AWS Jobs FOTA Sample nrf_inbuilt_key_delete...
Hello, I started to delvelop an program from mqtt simple, now that I almost finished I saw that mqtt is refusing to connect to my broker, I deleted all my code I wrote and...
hi ,,, nrf52832 , at first for bonding i will connect my device manually by scanning and after passing the data to flash , i will disconnect . in program i have set the timer...
I'm writing test code to verify the softdevice operation according to the spec.
The goes like this:
The central sends the feature exchange command, when the feature exchange...
Hello,
I have been experiencing corruption using a similar implementation to the USBD_MSC example. Even after the various SDK fixes suggested to the same problem outlined...
Hi Øyvind
I can't programing the target board.can you tell me On the "debugger" nrf9160DK ,What do I need to set?
I followed the Settings below:
On the "debugger" nrf9160DK...
Hi,
I am trying to setup a ble sniffer to make sure another one of my devices is sending the correct data to the central. But the nRF sniffer does not seem to be picking...