Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
Hi,
Using nRF Connect SDK 2.7.0 on an nRF9160. Using native tls, works fine, i can setup HTTPS connections.
Problems arise when i try to use MQTT with native TLS (with...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
SDK 2.3.0
We have a custom board with a few GPIO connected to various interrupt sources (Button, sensor interrupts, power connection etc.)
We are experiencing here sleep...
I'm trying to sample the 4 of the analog inputs on the nrf51822 at upwards of 10kHz and get the data out some how. Currently I'm using printf statements but that starts to...
I am porting my code (previously on 51822/SDK V12) to 52/SDK V14.
I have RTT logging working well on 51/SDK v12. In SDK V14 I noticed that the log module now is in experimental_log...
nRF52832
SDK14.0
Hi, how can I protect the bootloader from being overwritten? Ideally, I would never be updating the bootloader so it will be a permanent part of the device...
Hi
How stable is the RTT module and how trustworthy is it?
It is marked as unstable and I do not get any messages from the modules.
I use:
#define NRF_LOG_BACKEND_RTT_ENABLED...
Hi,
i would like to implement a very low power counter and used the template from this post . I've modified the example and used TIMER2 in counter mode triggered by LPCOMP...
Hi,
I'm trying to create a local network between an nrf51-DK and a mobile phone, android or iOS. The main goal is to be able to get TCP/IP connection between the nrf5x...
I am writing firmware for a BLE Nano device using the Nordic SDK 8.1. I was having problems where my device would suddenly stop printing to UART and stop trying to bond with...
I'm trying to set up a ble mesh with 3 servers and 1 client on an nrf52 PCA10040 dev kit. Upon debugging, I'm getting an error that says: '64, APP_ERROR: C:\Users\sesa463145...
I am using a NRF52-based platform and have BLE code based on the ble_app_hrs_c Hear rate monitor system.
Having set up for scan, I see many device (we have a lot of beacons...
After migrating from sdk 13 with buttonless dfu based app I meet follow error:
my app get FATAL error after exactly 3min. I guess it something related with power down mode...
I have a 3 channel setup on my SAADC module, which I sample according to a LFCLK timer. I notice after the first called to nrf_drv_saadc_sample() and receipt of the ADC results...
hi,everyone!
we use the example
"nRF5_SDK_14.0.0_3bcc1f7\examples\ble_peripheral\ble_app_uart\pca10040\s132"ble_app_uart,
we also defined
"#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
At the very end of this post from Nordic Info center I am doing the exact example at the very end.
infocenter.nordicsemi.com/index.jsp
This is the start to do a transmit...
Hello
I'm trying to track lost packets in a connection by showing the sequence number of each packet received. Specifically it's about an application that sends new measurements...
