Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Issue is similar to
devzone.nordicsemi.com/.../
I'm developing an application based on latest SoftDevice 130_1.0.0 and using two or more DevKits.
My application starts...
Hi. My app based on S130_1.0.0 and is run on DevKit with 51422 chip. App advertises and scans at the same time with next params:
adv interval = 20mS;
scan...
im using nrf51822. before entering DFU mode I want to save data in flash. but when I call pstorage within reset_prepare function, it doesn't jump to DFU mode !!!!
reset_prepare...
Hello guys, i'm new in nRF51 DK board, and i would like to flash the .hex file to my board, but when i do it the board automatically unmounting himself and reset with the...
hello there i want to send negative acknowledgement then what should i do?? like i want to send some data and then i want to send negative acknowledgement
i am trying to use yggdrasil for nrf51422 (pca10028) with sdk 10.0. after installing, i cannot see the com port. How do I flash "connectivity_115k2_with_s130_1.0.0.hex" with...
Hi everyone!. I am beginner for Nordic Devices
I want to use RTC Clock with softdevices
so I loaded the project ble_uart_s130 from examples.
and I changed code like...
I have a ble central device. Sending commands to UART in main() works well. Sending in on_ble_evt() doesn't work (only the first char).
But I see in your examples that you...
Hi guys,
I've almost got DFU working on SDK10. However I am having issues at post validation of the image, specifically in the function dfu_init_postvalidate() in file...
Hello all,
Thank you in advance for taking your time for reading this question. I'm developing a proximity application and I have programmed the nRF51 DK with the s110...
Hi,
I am trying to set up a small mesh network. Basically I have a couple of PCA10028 (v1.1.0) and I have flashed the mesh example:
github.com/.../BLE_Gateway
One...
Hello Everyone,
I have been working around BLE profiles for few months and i have made several tested for each service via MCP(android) everything works fine but now i...
Mt need is to do frequency measurement of 0.01Hz to 99.99 Hz
We need a clock of 1us that added to a timer of that start on when the pulse low to high event happens and...
Hi there,
I want to connect multiple nus devices to S120 central. After connection with device, it starts to scan again after the BLE_GAP_EVT_CONNECTED event. And there...
