We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
I am implementing a custom service with several characteristics, one of which is the current temperature. A second characteristic notifies the user if the temperature...
Hello,
I'd like to upgrade nrf51822 QFAC custom board firmware via DFU and change SoftDevice from s110 to s130. Because of larger (than s110) size of s130 I haven't enough...
Hello,
i am using the Visualgdb with sdk v 13.01. i have Nrf52840
i was trying to read the DeviceID of ADXL345
i am using API from this thread
devzone.nordicsemi...
I have used pstorage before but when I add scheduler to my project I face an error in update function of pstorage that in debug I found error_code : NRF_ERROR_NO_MEM .
any...
In short:
Is it possible to connect a nRF51822 s110 peripheral from a central without the need for sending advertising packets (by peripheral)?
If (hopefully) yes...
Hello,
I am trying to create an application that sends a notification from the nrf52 to a smartphone when a sensor reading exceeds a certain value. Would the immediate...
Hi,
I have designed and made a PCB with the nRF51422 chip on it. I am programming the chip externally using the P20 header pins on the nRF51-DK. I am not sure whether the...
What I have to do if I met this ? I round length to fit (len+4-(len % 4)). Is it right ?
if (!(IS_WORD_SIZED(m_start_packet.sd_image_size) &&
IS_WORD_SIZED(m_start_packet...
Hello,
We have problem BLE connecting to the nRF52832, if we use the method gap_init(), the "better" smartphones can connect(those who support BT 4.2). If we skip the gatt_init...
Hi,
I'm trying to program an external NRF52832 board with the NRF52-DK, per the instructions in this post .
Programming works fine, but the code doesn't execute after...
Hi,
I'm trying to do DFU in my app, I almost complete it, I met a problem that my app flashed back when I sent 04 to the device.According to the DFU doc,after uploading firmware...
Hi,
I'm using the ADC of nRF52832 on nRF5 SDK V12.2. The setting as attachment. I found that it just do sample one time. But I have use timer to call nrf_drv_saadc_sample...
The scenario like this:
A is BLE peripheral with firmware (ble_app_uart under nRF_SDK_13.0.0_04a0bfd), if no filter,any central can cenncet to it, but I just want B can cennect...
Dear all,
Help please,
I'm evaluating ble_app_uart (Central/Peripheral) but I don't understand how to disable the echo I have on the RTT USB VCP
When I send data from...
