My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
nRF5_SDK_12.2.0.
app_timer_freertos.c
app_timer_stop() call xTimerStop/xTimerStopFromISR with timer_id parameter.
It seem to must use hTimer parameter.
It's bug?
MY application is using SDK 12.2, SD132 v3.1 and freeRTOS. I'm trying to debug a sensor that uses TWI. When I enable logging. #define NRF_LOG_ENABLED 1, NRF_LOG_BACKEND_SERIAL_USES_UART...
Hello Everyone,
I am new to keil and nrf51822 programming.
Currently I am using softdevice s130 with hex file for bootloader from
folder : nRF5_SDK_11.0.0_89a8197\examples...
Hello,
I would like to instruct my application to read the battery voltage on my nRF52pca1040 DK, I am intending to do so through the SADC.
I will feed the board with...
Hi,I have some problems in debug with experimental_ble_app_buttomless_dfu project.
First i build the experimental_ble_app_buttomless_dfu project,so i get the app_buttomless...
We am improvising nrf blinky application, we have got stuck in a problem, after button is pressed from nrf52-dk code goes into forever loop and after a while connection is...
I have two nrf51822 modules and first one is sdk8.0.0 / s110 / peripheral device, second one is sdk10.0.0 / s130 / central device. I've sent a 10-character data array like...
Using:
SDK14
Softdevice132 V5.00
app_uart driver with legacy, no easy dma.
UART is set up with hardware flow control.
The pins should be set up correctly: rx-tx , cts...
i want to konw ble evt struct 's content of meannig . i want to find what's the return value when packet send fail and what is the channel id different from other ruturn value...
Hello,
I want to falsh nrf51422 device. I ma developing software using Eclipse and SDK_7.2.0.
The soft device is 130. I have build the project successfully and Hex/elf...
Hi
I'm trying to communicate between nrf51-DK and arduino using twi. I was able to send data from nrf51-DK to arduino using nrf_drv_twi_tx but when I'm trying to send the...
Reference PWM_driver sample code,
I set the customer status of the LED,
And it also can change status by button,
static void bsp_evt_handler(bsp_event_t evt)
{
void...
Hi,
I want sample code for configuring baud rate of UART from mobile application (nRF Connect). So I don't need to hard-code the baud rate in my program.
Please share...
With version v2.0 of S332, I checked for a return of BLE_ERROR_NO_TX_PACKET when using the ble_nus_string_send function. I use this test in a routine which writes buffers...
I called these command:
nrfjprog -f NRF52 --eraseuicr
nrfjprog -f NRF52 --program app.hex --sectorerase
During the eraseuicr I see:
Erasing UICR flash area.
Applying...
