Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
I have a peripheral device with a custom service with 3 characteristics all of which send data to my central via notification. I've supplied each characteristic metadata with...
Hi
I have seemingly successfully created a firmware that sends a continuous carrier wave using radio_test.c from nRF5_SDK_12.1.0_0d23e2a/examples/peripheral/radio_test...
Hi there,
i am running bootloader code but facing a error that is "pstorage_platform.h" not found.i am using code from given path which is from SDK10.0.0 .what should i...
Hi,
I am applying IRK on ble_app_hrs_central and ble_app_hrs peripheral on nrf52832 and S132 v.2.0. ON the central side I want to see if the IRK was resolvable or not....
Hello.
I would like to run DFU experimental_bootloader_secure_usb example on NRF 52840 but
the USB port does not recognize my device.
I tried with both 5.0.0-2Alpha and...
Greetings,
NEXUS 6P
I am trying to run the Android-Image-Transfer-Demo with a nexus 6P. So the application compiles and loads fine into the phone, but whenever i try to...
Hi Support Team,
Is there any plans to release the bluetooth 5 mesh examples with all SIG models support?
If yes when it will be released?
Thanks and Regards,...
hi,
is it possible to set major and minor values in ble_app_uart example in sdk14.1. and advertise it. now it is advertising rssi, uuid, mac id and device name. i want...
Can I get the Altium Library for the nRF52840? I downloaded the Altium reference design but when I try to create a library for this design Altium indicates it cannot be created...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Dear Nordic employee:
1、 what do I have?
I have two thingy52 develop kit（nrf52832）
2、what is my purpose?
I want to develop a dome that sounds can transfer between...
We are using nRF52840 as SPI slave and imx7 as SPI master.
Data sent by imx7(master) is received at nRF52840(slave) correctly, however the data sent by slave is not received...
