Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
We try to use "ATT_MTU" and "Data length extension (DLE)" to expand a packet in S132 SDK 14.0.0.
When we set "ATT_MTU" > "DLE", please tell me what happens?
...
i am in very strange problem and was unable to debug it
i am using following code to write 16 bytes data to flash memory, my app hangs after executing custom_flash_write...
Hi all,
i'm trying to use the function of power warning with s132 and nrf52 with sdk 11.
i use the function
err_code = sd_power_pof_threshold_set( NRF_POWER_THRESHOLD_V27...
I am running example: nrf5-ble-tutorial-advertising on a nRF52-DK.
with SDK 11 and s132_nrf52_2.0.0 softdevice.
When I flash the code to the nRF52-DK, LED1, LED2, LED3 and...
Hello,
I'm using Ceedling, Unity + CMock to implement unit tests but I'm running into issues when it comes to mocking nrf_drv_gpiote.h.
I'm trying to test a file, call...
Hi Nordic Engineer, I refer to your previous post title "Running micro-ESB concurrently with BLE" and gonna to use it on our project.
I test it on 4 pcs of DK board, found...
I have a problem using ble_advertising_restart_without_whitelist(). According to the documentation (as I understood) it should start advertising without whitelist even if...
Hi all
When i am reading ANCS code, i have some questions. SDK 12
Question 1: when ble device are connected with ios, the pairing is wrong, how to handle validation...
I am attempting to port a custom ble service from sdk12 to sdk 14 and am a bit confused as to how to increase my uuid count. In sdk12 I did it like this:
uint32_t err_code;...
Hi
I am using wireshark 2.0.1(64 bit).When i am trying to capture the ble packets it showing error.I have attached the Wireshark error message.BLE Sniffer version 1.0.1.I...
In the Bluetooth Light Controller example for the client in main.c these constants are defined:
#define SERVER_COUNT (3)
#define CLIENT_COUNT (SERVER_COUNT + 1)
Why...
Hi Nordic,
Sorry if I missed and repeated a question, just point me to the previous answer if it has been posted before.
I am trying the DFU example found in the SDK...
Hello,
I'm wondering that it is ok to route ANT line through board-to-board connector to chip antenna.
Because there is no space to place nRF52832 and chip antenna together...
Hi,
I've seen that SDK 12.3.0 contains a new version of the application sample using the Eddystone protocol for BLE. I would like to know if this version is compatible...
I am using the template example for S130(works fine).
I tried adding a simple Pin interrupt on the code but it didn't call the pin interrupt handler everytime I press the...
