Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi,
I am new to firmware engineering. I have a simple and basic question.
If there's Timer A and B, and both interval is 100ms, what happens to the timeout handler functions...
I want to add some configuration files to nrf52, so can I write data in flash and read when I want.......I have the example code of twi master_twi slave but it engages the...
I have followed the instructions for sniffing ble packets with wireshark. Errors would occur when using 2.2.5 so I switched to the latest development version. See this question...
Hi, I am developer of indoor location tracking solutions for asset tracking applications, actively looking out for new technologies, i would like to understand what are the...
Normally I am using nrf51 for peripheral(sdk 8.0.0 s110) and central(sdk10.0.0 s130) device. But I want to use nrf52 for just central device. I tried nrf52 for central(with...
Hello All
Currently i am using nRF51422-DK (PCA10028) Board .I am planing make mesh network using nRF51 devices.i go through the mesh network introduction document which...
Hi,
I'm trying to set a button as an interrupt source. I wrote this code:
void Init(void){
pwrmng_MainStatus = PWRMNG_STS_STARTUP;
//LED
#ifdef DEBUG_LED
nrf_gpio_cfg_output...
I want to read the status of LFCLK,but I find that ,the value I have readed is awayls zero! my code is follow :
LFCLK_State = ((NRF_CLOCK->LFCLKSTAT) >> 16) & 0x00000001;...
Hi,
I had done secure OTA in nRF51 DK board using SDK 12.2.0 and s130 2.0.1 softdevice. Now, i am trying to same thing with my custom Board RL-51822-A1.
For that first...
I cloned the demo project inside the Keil MDK5, from the following path:
pack installer
device = "nRF51822_xxAC"
examples = "uart_pca10028, UART_Example_Application...
Hi,
I want to use the nRF BLE Sniffer to detect wether a connection (between my fitness tracker and smart phone) is present or not.
I am able to get the advertisement...
hi,
I am struggling to create custom service to send the simple message to the client device where both devices are nRF52832 (Server and client). when I receive the message...
I have 2 of the nRF51 Dev. kits and have been ble to run Blinky, BLE_UART and set up the 2 dev kits so that I can send data from one DK to the other and to an external board...
Hi,
I tried to flash the mbed FOTA bootloader on my nrf51 DK. I copied the bin file to the bootloader device. It said the storage on the device is to small. Now it won...
