Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
hello, I started working on BLE mesh using nrf52832 QFAAE1. from hardware side i have custom self design nrf52832 QFAAE1 lot's of board, and every board working, i verify...
Is there a BLE development board that supports extracting IQ data from raw MCPD ranging？ Does nrf5340dk support users to extract IQ data for the development of ranging algorithms...
Hi, the nordic team
I am working on thread protocol using SDK version 2.9.1.
I use the SED device,My poll is 1000 ms. How can I receive messages from my parent node when...
I work for ChannelSounding on nRF54L15.(NCS3.0.1)
I measured the distance using two nRF54L15-DKs. The actual distance was 3m. The average measurement result is shown below...
I know that BLE is not suitable for high-volume streaming.
So how do BLE earphones stream audio?
Does it use with bluetooth classic protocol?
And I coundn't monitor...
Hi,
I've one central and one peripheral devices. I'm trying to make a connection between them, perform a bonding process and finally add the peripheral id in the whitelist...
Hello All
I am developing BLE based home automation system using nRF51422 DK for my research activities. now i am planing to make separate PCB nRF51422 device alone. i...
Hi,
I'm trying to get the RSSI of incoming 802.15.4 packets using otLinkRawGetRssi() , but I need only RSSI from one specific device. I tried to use whitelist ( otLinkSetWhitelistEnabled...
Hi, I ran the example code ble_hrs_c in nrf51822 16KB RAM version and 32KB RAM version. The 16KB RAM version works fine. But in the 32 KB RAM version, peer_manager_init(true...
I modified the HTS app in the nRF toolbox to test adding other services like below.
In detail, I added mDICharacteristic field to save the information of System ID...
Hello,
I developed a Nordic board with 2450AT18B100 chipset antenna. I follow the design of Solar Powered Sensor Beacon.
infocenter.nordicsemi.com/index.jsp
I test...
Hi, I'm building a product with use this kit www.nordicsemi.com/.../nRF52-DK and I would like of know how write the firmware in others CIs to can use in my circuit board....
Hello,
I am currently working on project that uses BLE peripheral and BLE central for automatic sensor calibration on custom board. There is an initial connection where...
Helllo All,
I designed on custom board (nrf51822 and used 4 programming pins(swck,swi,gnd,vcc) but how to program/flash the soc?which segger i need to purchase?
Hi There,
I am
Using Linux as host platform
I'm able to successfully compile and download the example to the nrf52dk.
But I didn't understand how to debug the example...
I'd like to get peer address after the connection between nRF52 and other 6lowpan device is established. This address will be then used to create a TCP connection with some...
Hi All,
I am using the Nordic nRF52 nrf52832 device to read a value in from an Android device. The value will be between 5 and 60 seconds. I'm using the experimental_ble_app_blinky...
I would like to change UUID programatically,initially we are trying to establish connection between phone and beacon.
We tried to change BLE_GAP_ADV_TYPE_ADV_NONCONN_IND...
Hello, nordic team；
I want to create a DFU for the ANR + BLE device in the nRF5_SDK_12.3.0_d7731ad \ examples \ dfu \ experimental_ant_bootloader routine.But I use this routine...
