Hello,
I just received my Thingy:91X which I purchased through DigiKey. I am trying to connect it to hello.nrfcloud but I keep getting the following message: " The fingerprint...
With reference to the Thingy:91x reference design, I see that the LNA (SKY65943-11) on the GPS signal path is powered by one of the switching converters from the nPM1300:...
Hi,
I'm using cdc_acm to create two COM ports on a PC -
// USB support
& zephyr_udc0 {
cdc_acm_uart0: cdc_acm_uart0 {
compatible = "zephyr,cdc-acm-uart" ;
...
Hi,
We are having issues with this part bridging on our via-in-pads. We are using 2oz finished outer layer copper.
Do you have any footprint recommendations for 2oz copper...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Dear Nordic Support Team How are you? Currently we are looking into how to configure, compile and run a full-fledged NRF5340 project which should provide us with:
- Latest...
Hello,
once in a while we are experiencing ZEPHYR FATAL ERROR. It's very hard to reproduce on purpose and investigate in detail. But it looks like t->fn() somehow becomes...
Hello,
I'm using the SDK 11.0.0 and S130 on both sides, and the projects ble_app_uart_c and ble_app_uart to connect a central and a peripheral through BLE. I was doing some...
Hi..
i am using nrf52 and my custom made android application.
softdevice is 132.
in that am able to do DFU for application file with android master control panel.
i used...
Hi.
I will make clock.
I use RTC2 + Softdevice. (PCA10040 , NRF52832 , s132_nrf52_2.0.0_softdevice.hex )
Base Source code = nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral...
It seems to me that Nordic has implemented only a part of the Current Time Service.
I want to get the time zone in addition to the year, month, day, hour, minute, second...
Hi.
I'm developing firmware based on github.com/.../S130_LBS_client_server_central_peripheral example. I installed third party Softdevice s130, and with example of peripheral...
I have modifed the nus_uart(peripheral) to add static pass key in sdk 10.I used my mobile phone to test the functionality and it works as expected[asks for the passkey when...
Hi,
I'd like to put a BLE central in low power between two scan.
actually I use the example Ble_app_uart on a dk board PCA10028
and a second dk board as advertiser with...
Hi,
I am trying to get the SPI Slave working but was hoping to find a how-to. Is there an example of the SPI Slave for the S110 Soft Device (7.3.0)?
Currently, I am...
Hello,
I am developing custom HAL driver for SPI in NRF52 (PCA10040). The problem is that using the EasyDMA MAXCNT registers value must be between 1...255. It implicates...
Hi,
I am using nrf_pwm_noglitch.c from here . Is there a way to stop the pwm cleanly?. I would like to have a nrf_pwm_deinit(); similar to nrf_pwm_init(). Currently I set...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
About "ble_app_multilink_central" for the reference.
This code shows me below sequence.
Scan->connect request->get connection...
Hi,
We have an application where we have very very slow vcc risetime and therefore we have an external watchdog reset circuit connected to the -reset/swdio pin in order...
Hello,
the available QDID for nRF52x refers to Softdevice which has no IoT capability, being this a work in progress.
When this will be ready, will Nordic release a new...
