I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi. I'm trying to flash Secure DFU bootloader together with my application. I tried to flash bootloader and then main application, but the device stays in bootloader instead...
ppi.zip Hi, I am using radio with ppi to advertize packets as shown in the mainc file attached. Even after allocating the access address of Bluetooth on line 196 as set_address0...
Hi there,
I am trying to measure environment below 0 C but the app reboots and refuse to connect with thingy52 at lower temperatures. Do I have to set up anything else...
hi ,
I have a question about rtc.In my project ,I use rtc1 for app timer and rct0 for low_power_pwm.The problem is that I dont't have any idear to enable rtc0 instead of...
hello:
i meet some trouble,i can find the service,then appear error "BLE_GATT_STATUS:10a".
#define BLE_GATT_STATUS_ATTERR_ATTRIBUTE_NOT_FOUND 0x010A /**< ATT Error: Used...
Hi,
I am trying to use the nRF51DK (PCA10028 v.1.2.2).
I cannot get Windows 7 to recognize it via USB reliably. I have JLink v6.16a installed and when I plug in the board...
I have variable values coming out of a terminal at all the time. I using this command:
void in_pin_handler(nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
...
Hi All,
I am developing a ble applications and am unable to get pins 9 or 10 to work as gpio. I understand that this is because, by default they are used by the NFC.
...
How do I limit the number of peers that are stored in the peer manager? I don't see a configuration variable. I don't know the addresses of peers before hand, so I don't think...
Currently, I am trying to develop nrf51822 ( MDBT40 ) using Nordic SDK v12 (S130). The programmer I used is DAPLink from RedBear .
I am wondering how to make program to...
Working with the NUS, I sometimes see ble_conn_params_on_ble_evt getting called in a way that will cause the data being passed through NUS to stop. Not all the time, just...
Thats the problem.
On Windows7, 64 bit, with the Bluetooth Stack from the USB BLE-Stick happens the following:
Windows (master) initiates the connection, sends a security...
