Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
Hi
I am running SD 132 2.0.1 on nrf52832 rev 1 and i am getting a chip lock reset occurring. (I have cleared the flags as per the errata and reset pin flag is not present...
....\R2D2_build\R2D2_Firmware.hex: Error: Q0122E: Could not open file '....\R2D2_build\R2D2_Firmware.axf': No such file or directory
keil gave me that error. i did research...
Hi
When I used ANCS, there is "bluetooth pairing request" notice shown on the iphone, if choose cancel, then 51822 went to reset, why is that happen?
iOS:10.3.3
NRF51822...
nrf5_SDK 12.3.0
nrf52832
softdevice 3.1
My app used timer for buzzer and led.
This timer call itself, and variable is discount.
This is normal mostly, but in somtimes...
I am working on reading ADXL362 through SPI on PCA10040.I used demo spi in nRF5_SDK_13.1.0.
here is my main code:
bsp_board_leds_init();
APP_ERROR_CHECK(NRF_LOG_INIT...
I am developing on the nRF52 boards with a capacitive sensor. I followed the tutorial in this link and created a custom service with 3 read characteristics. I am able to use...
NRF52 pca10028 DK - SDK14 - Arm GCC (Eclipse) - SD 5.0.0 - bootloader_secure_ble
Using either nRFGo Studio or eclipse to program the flash (it does it with both)
I can...
Hi,
some time ago we ordered 3 PPKs. I tried one under a Mac with VmWare / Win7 with a PCA10040 board. It was working but I got surprising graphics. When I came back from...
Hello,
I am just using the SDK13 on the nRF52832 together with the experimental BDS example (I modified it to the point where it seems to be working fine so far).
Now...
The following does not allow me to define NRF_DFU_HW_VERSION in my makefile, I get redefine errors due to this broken if else in def_req_handling.c:
#if defined (NRF51...
I want to evaluate the nRF52 SDK , but don't get how to install it.
The Getting Started section mentions an MDK installer. However, I cannot find any such installer inside...
Using the nina 112 with nrf52832 SDK 13
I have got a problem with the I2S Interface.
I configured the RESET Pin as normal PIN. Tested with GPIO as Output it worked. If im...
Can we build the FW manually and upload to the Thingy via the OTA uploader? We built the FW, created the DFU, and inserted the .zip file in the iOS app, however get an Error...
Hello!
I am working on a project. The goal is to retrieve every seconds some acceleration data from the ADXL362 accelerometer.
I configured the spi in blocking mode...
Am i right in thinking that if GPREGRET has not been set then we can not guarantee what value it will be?
I.e on power up we can not guarantee that its value is 0.
