Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I had the following setup, two app_timers triggering blocking SAADC reads in the callback functions
app_timer 1000ms triggering 1 Blocking SAADC read (For battery service...
Hello,
I use sdk 8.0.0 and s110. I read this blog
And I did not understand some terms;
Application processing(for example 2ms each adv interval)
Number of packets...
Hi,
I am using the nRF51 Dongle (PCA10031, V 1.1.0) and pc_ble_driver.py to create a custom script for testing purposes. But there seems to be a maximum limit for the measured...
I met a problem when delete bonding information on android central, i actually can't connect to the nrf52832 peripheral again, until i totally clear it's peer list and bond...
Hi all,
I am trying to control a speaker using the i2s output of the nrf52832 mapped into a TAS2505 from TI. I am able to play sounds in the speaker but my issue is that...
I am trying to use the eddystone example I found in the ble_prepheral/ble_app_eddystone/pca10040 folder in SDK14.2 with my nRF52832 development board but I get the following...
i found this link on nordic website to learn ARM with Nordic SOC.
www.nordicsemi.com/.../Nordic-ARM-Lab-in-a-Box-University-Program
Do you know where is the link for...
Hi,
I am able to program a SparkFun nRF52 breakout board via nrf52 Dev Kit using Segger Embedded Studio. However, I am not able to achieve the same results using nrfjprog...
I am facing some issue while writing to i2c. On first i2c write , device is working but after that when i tries to write anything, code is stucking in loop.
void sensor_sleep_mode...
Hi,
I'm trying to port my project from SDk12.1 to SDK14.0, I've got everything working fine except the DFU process. The main issue is that we've got some devices distributed...
Hello,
I am designing a custom board with NRF52832 IC. I followed all PCB consideration suggested by Nordic.
This blog suggests, If using a PCB antenna, the matching network...
This question is similar to this thread:
devzone.nordicsemi.com/.../
However it was framed differently and didn't really clear anything up for me.
Say my application...
Hello,
I have an application that has to be ported to the newer Softdevice version. I've already ported my application to the SDK 13 and tested it with the new Softdevice...
