Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi,
we have developed a board that is using the nRF24LE1 chip. For test purposes I do want to toggle every possible pin. My first step is to develop this simple test code...
Hi all,
I am on the DK-52 with the SDK 13.0.0.
After erasing the device, I follow this steps:
upload the softdevice
nrfjprog --reset --program s132_nrf52_4...
Hi Forums,
I work 51822 custom board.
I try to add Buttonless DFU so I test the "experimental_ble_app_buttonless_dfu" compile is good.
But flash to the board can...
I am building a Bluetooth Mesh network with multiple types of devices.
The provisioner is now capable of provisioning and configuring multiple instances of Device A but i...
I am using nrf52832 with softdevice s132 v3.0.0, sdk 12.2.0 and FDS.
I am using sdk_config.h to configure various modules in my project.
Earlier config: Using Timer1...
Dear nordic devzone,
When trying to build the "ble_app_hrs_c" example project it does not build in SES.
Output/ble_app_hrs_c_pca10056_s140 Debug/Obj/peer_manager.o:...
Hi,
I'm currently investigating the Bluetooth mesh using the SDK for mesh alpha 0.10.0, I was wondering about the limitations on the re-transmission of messages. The current...
this issue might also be one of others than myself
my main development environment is based on linux ... firmware, QT, android and whatever comes along ... i used to write...
Is there native support for hardware coex lines? If we have a WiFi chip that produces a TX Active signal, can we hold transmit from the nRF52840 till that transmit is finished...
I have bought a Tayio Yuden EYSGJNZWY Bluetooth module, which is in fact just a Nordic's nRF51822 (256KB Flash and 32KB RAM) with added antenna. Tayio's files say that the...
Hi,
I have built an application which is based on BLE and protocol that supports high frequency sampling of sent messages. I tried to achive that using only BLE, but it...
Hello,
I am designing a custom board with NRF52832 IC. I have a query regarding routing of traces.
In my design, I am not using all pins of IC. Do I need to route traces...
Hello,
I am designing a custom board with NRF52832 IC. I followed the same layout design as suggested by Nordic.
But , I made some additions to reference layout. I added...
I'm trying to set up a gazell device with a channel table that is 16 channels long. This is for a pairing application where the host has a channel table that is 6 channels...
