Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello, I have the Beacon Development board and the sample firmware downloaded and up and running in the Keil MDK IDE. My specific application requires some code to execute...
Hi,
i want to add a current time service to nRFgo. In particular for the glucose measurement profile.
Any suggestions for this???
I add manually the current timer service...
Custom nRF51822
SD130
SDK V11
So sometimes my disconnects seem to fail, the return code says success, but when I try to reconnect I get an error 18, NRF_ERROR_CONN_COUNT...
Hi,,
In the GPIOTE example code(I use TIMER2), I want to control the cc register values by accessing the TIMER2_IRQHandler routine. I tried enabling the interrupt for compare...
I found there is no ble_app_hrs_rtx PCA10040 ,
and release note said:
nRF5 SDK v11.0.0
Heart Rate Application with RTX: Support for nRF52 has been removed.
...
Hello,
I have some MDBT40 modules from Raytac that are blank. I want to flash some code (anything at this point) using the STLink/V2 programmer , SWD interface, and OpenOCD...
So I've got my device running, set up two services with some read and write characteristics and it all works like charm now.
But now I want to react to values written into...
I am using GPIOTE to response to transitions in some GPIO pins. This code is added to the BLE UART example code (ble_app_uart_c with S120) from SDK 10. The code is already...
Hello
I have some trouble with my DFU bootloader, because I changed the BOOTLOADER_REGION_START.
This is, because I need some more space for bootloader.
Do I have to...
Hi,
Hardware:PAC10040
Platform: nRF5_SDK_11.0.0_89a8197
Master Control Panel: V4.1.3
1.If dfu has started and transported some data, then disconnect bluetooth and...
I was able to setup gazell frequency hopping communication between a device and a host. Device:nrf51822+PA/LNA(RFX2401);Host:nrf51822+PA/LNA; They can communicate at a long...
Dear sir,
can you provide any chip which is having RSSI and compatible with NRF24LE1 .We have an application in which we have already have a transmitter based on NRF24LE1...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_uart_c" as reference.
As "ble_app_uart_c" source code, it already knows Service UUID.
uint32_t ble_nus_c_init(ble_nus_c_t...
Hi!
I'm trying to get the MPU-9250 chip working through SPI with my nRF52832. But I don't seem to have much luck.
I have created a basic program for testing, based on...
I am using SDK9.0 to develop a ANCS project,now it accept the incomming call ,message,QQ,Wechat successfully,but the question is how to distinguish the message,QQ and Wechat...
