According to the nRF52832 Product Specification, “A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply range, may...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-3-dfu-with-external-flash/
I have this exercise...
Hi,
I noticed in the nRF54L QFN48 reference design, for the NRESET pin, there is an RC filter (1Kohm series R and 3.9pF shunt cap). What's this for and is it necessary?...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I want to request AGNSS information from nrf cloud services using my nRF9151DK board. As a first step, I flashed the nRF Cloud multi-service application onto my DK...
Hi,
I'm using cdc_acm to create two COM ports on a PC -
// USB support
& zephyr_udc0 {
cdc_acm_uart0: cdc_acm_uart0 {
compatible = "zephyr,cdc-acm-uart" ;
...
Hi.
I will make clock.
I use RTC2 + Softdevice. (PCA10040 , NRF52832 , s132_nrf52_2.0.0_softdevice.hex )
Base Source code = nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral...
It seems to me that Nordic has implemented only a part of the Current Time Service.
I want to get the time zone in addition to the year, month, day, hour, minute, second...
Hi.
I'm developing firmware based on github.com/.../S130_LBS_client_server_central_peripheral example. I installed third party Softdevice s130, and with example of peripheral...
I have modifed the nus_uart(peripheral) to add static pass key in sdk 10.I used my mobile phone to test the functionality and it works as expected[asks for the passkey when...
Hi,
I'd like to put a BLE central in low power between two scan.
actually I use the example Ble_app_uart on a dk board PCA10028
and a second dk board as advertiser with...
Hi,
I am trying to get the SPI Slave working but was hoping to find a how-to. Is there an example of the SPI Slave for the S110 Soft Device (7.3.0)?
Currently, I am...
Hello,
I am developing custom HAL driver for SPI in NRF52 (PCA10040). The problem is that using the EasyDMA MAXCNT registers value must be between 1...255. It implicates...
Hi,
I am using nrf_pwm_noglitch.c from here . Is there a way to stop the pwm cleanly?. I would like to have a nrf_pwm_deinit(); similar to nrf_pwm_init(). Currently I set...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
About "ble_app_multilink_central" for the reference.
This code shows me below sequence.
Scan->connect request->get connection...
Hi,
We have an application where we have very very slow vcc risetime and therefore we have an external watchdog reset circuit connected to the -reset/swdio pin in order...
Hello,
the available QDID for nRF52x refers to Softdevice which has no IoT capability, being this a work in progress.
When this will be ready, will Nordic release a new...
Hi,
I want to use the NRF51822 without the Bluetooth functionality. Is it possible to leave the pins ANT1, ANT2 and VDD_PA unconnected? If no, what is the cheapest way...
Hi,
I'm using PCA10040 board, There i connected the fuel gauge IC via TWI communication.
There pca10040 will acts as master and fuel gauge IC will acts as slave.
While...