Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hi all!
I am developing an nRF52 application that uses RTC interrupt to measure an ADC value every 100 ms. Depending on the measured value the chip shall either go back...
I am using nRF 52 development board. Using Keil to program it. Its has 4 buttons. We can easily detect when a button is pressed, but is there a way to know for how much time...
I'm using the following code to make the beacon sleep:
static void on_ble_evt(ble_evt_t * p_ble_evt)
{
uint32_t err_code;
switch (p_ble_evt->header.evt_id)
{
case...
Hi, Developer Zone!
Can pm_peer_rank_highest function return NRF_ERROR_STORAGE_FULL code?
There is no this error code in description for function, but in the code I see...
Hi
I am sending my BT module with nRF51822 for some regulation test and the Test Lab is using Anritsu MT8852B to communicate with my module through USB-to-UART adaptor and...
Hi team,
I have seen the example of crypto in the SDK_12.3.0. I want to learnt it. But I don't know how to use it, because there is not keil project file, and I hadn't...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hello,
I have adapted the ble_app_uart_c project for a custom board based on nrf52832. The application already works fine, however, my peripheral is sending four packets...
Hi,
I decided to use nRFUART Example which is inside of the Master Emulator.
I am using nrf51 dongle for connecting peripheral devices.
When I run the nRFUART Example...
Hi,
I am porting my code from SR3 v1.0 to SR3 v1.1 now.
I have a problem in debugging SR3 v1.1.
In SR3 v1.0, it's fine in MDK-ARM debug session. I can set break point...
I have been working on integrating FDS into an SDK13 project using SES v3.24.
I'm not sure if the memory allocations are set correct. If I increase the FDS_VIRTUAL_PAGES...
So I have been integrating FDS into a project under SDK13. It's based on an example that Hung updated for SDK12.1. So after init of fds the method fds_test_find_and_delete...
This crystal, which is used the nRF52 dev boards and reference designs, is now "not recommended for new designs". I could find another crystal that meets the spec, but just...
Hi,
i'm currently try to figure out how to use an Android device as an IPv6 Server through BLe sending UDP packages. One of my collegues tried this example as it was discribed...
I'm using Nordic nRF5840 and I want to send the micro controller's temperature every 1 second via Bluetooth. Can you tell me how to implement it?
I found an example named...
