I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
nRF5_SDK_12.2.0.
app_timer_freertos.c
app_timer_stop() call xTimerStop/xTimerStopFromISR with timer_id parameter.
It seem to must use hTimer parameter.
It's bug?
MY application is using SDK 12.2, SD132 v3.1 and freeRTOS. I'm trying to debug a sensor that uses TWI. When I enable logging. #define NRF_LOG_ENABLED 1, NRF_LOG_BACKEND_SERIAL_USES_UART...
Hello Everyone,
I am new to keil and nrf51822 programming.
Currently I am using softdevice s130 with hex file for bootloader from
folder : nRF5_SDK_11.0.0_89a8197\examples...
Hello,
I would like to instruct my application to read the battery voltage on my nRF52pca1040 DK, I am intending to do so through the SADC.
I will feed the board with...
Hi,I have some problems in debug with experimental_ble_app_buttomless_dfu project.
First i build the experimental_ble_app_buttomless_dfu project,so i get the app_buttomless...
We am improvising nrf blinky application, we have got stuck in a problem, after button is pressed from nrf52-dk code goes into forever loop and after a while connection is...
I have two nrf51822 modules and first one is sdk8.0.0 / s110 / peripheral device, second one is sdk10.0.0 / s130 / central device. I've sent a 10-character data array like...
Using:
SDK14
Softdevice132 V5.00
app_uart driver with legacy, no easy dma.
UART is set up with hardware flow control.
The pins should be set up correctly: rx-tx , cts...
i want to konw ble evt struct 's content of meannig . i want to find what's the return value when packet send fail and what is the channel id different from other ruturn value...
Hello,
I want to falsh nrf51422 device. I ma developing software using Eclipse and SDK_7.2.0.
The soft device is 130. I have build the project successfully and Hex/elf...
Hi
I'm trying to communicate between nrf51-DK and arduino using twi. I was able to send data from nrf51-DK to arduino using nrf_drv_twi_tx but when I'm trying to send the...
Reference PWM_driver sample code,
I set the customer status of the LED,
And it also can change status by button,
static void bsp_evt_handler(bsp_event_t evt)
{
void...
Hi,
I want sample code for configuring baud rate of UART from mobile application (nRF Connect). So I don't need to hard-code the baud rate in my program.
Please share...
With version v2.0 of S332, I checked for a return of BLE_ERROR_NO_TX_PACKET when using the ble_nus_string_send function. I use this test in a routine which writes buffers...
I called these command:
nrfjprog -f NRF52 --eraseuicr
nrfjprog -f NRF52 --program app.hex --sectorerase
During the eraseuicr I see:
Erasing UICR flash area.
Applying...
