I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hello,
My name is Calvin and I am tasked with testing the NRF52840. I want to create my own development board for prototyping a project, but I do not want to keep plugging...
Hello Nordic team,
I'm currently developing on the nRF5340 and recently encountered an issue related to BLE advertisements . After thorough debugging, I was able to confirm...
Hi, I have issues configuring PSM together with RAI on my nRF9151-DK. I am trying to send UDP packet, wait for response and go to sleep for several minutes trying to consume...
I'm trying to implement DFU over USB through Serial Recovery, for a custom board using a nRF52840, following the nRF Connect SDK Intermediate Lesson 9: Exercise 4 – DFU over...
Hi Nordic,
I want to implement a LED blinking like below pseudo code. I'd like to use Timer x n , GPIOTE, PPI since it doesn't consume any CPU time. for (10 times) { for...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Description:
I am working on an application using the nRF9160 and encountered an issue where the #MQTTEVT event is not triggered after connecting to an MQTT broker using...
Hi,
I am trying to create a trilateration system with 3 initiators and 1 reflector (Hopefully multiple reflectors in the future) on the nrf54l15. The channel sounding with...
Hey all,
I try to flash the SuperMini nRF52840 using my NRF52-DK over Debug HW (SWDIO pins). I try to flash the Zephyr blinky example.
I think I already got it (at least...
I can flash the chip. I can run the debugger. I can go to the connected devices, select the device, go to the little "plug" symbol on the RTT, and select it. That brings up...
Hi there,
I'm working with a custom board based on the Raytac AN54L15Q module and encountering higher-than-expected power consumption when trying to profile using the system_off...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hello,
I'm developing on a custom nRF5340 board without an external clock source - nRF Connect v.2.9.0. For my application, I'm using the internal system clock with this...
Hi,
I am testing the Bluetooth function on my custom board with nRF5340 CLAA chip. I have tested the clock, I2S and SPI on this chip previously and they all worked perfectly...
Hello Nordic team. Please let me know if you can provide assistance or advice on this issue. Any help is much appreciated.
Our issue:
Myself and my team are wondering...
