Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi all:
I'm am a beginner switching over from the Arduino IDE and the feather nrf52.
I am able to successfully program the sparkfun nrf52 with a SoftDevice, bootloader...
Hi all,
I have three nRF52840 DK. I would like to play around with Bluetooth Mesh, but I can not find any examples. It would be perfect if in the end I will have a gateway...
hi,
I am using Segger Embedded Studio and trying to store a data into flash memory by fstorage. For that i put the following in the flash_placement. xml file
<ProgramSection...
Hi,
I have a adafruit Feather M0 BLE with nRF51822. Wanted to know if there is a library which can help talk MQTT using just Bluetooth. Planning setup the board to talk...
I made eclipse environment and get rtt log with
JLinkGDBServerCL.exe (set in eclipse environment)
J-Link RTT Client
so I start "Debug" in eclipse, and start...
I want to run the nrfutil to do some test, after I clone the source code from github.com/.../pc-nrfutil
I run the nrftutil directly from the source code without installing...
We propose to use the SKY66112_11_203225L, but would also prefer to use Zephyr ( Or some other RTOS, like mynewt). I am aware of how to use the softdevice, but since neither...
www.silabs.com/.../ble-mesh
Do we have similar test program as if silicon Lab?
As I am about to build some PC/Android program to demonstrate the Bluetooth Mesh Device...
I use another jlink ob board to connect to nrf52832, and when i use j-link v6.16c，it give a warning prompt "The connected j-link is defective", and i use jlink v5.12f, when...
Hi,
We have some devices in the field, and I'm occasionally seeing reboots due to NRF_FAULT_ID_SD_ASSERT. I'm logging the id and pc passed into app_error_fault_handler...
SDK13, S132
Project stopped after start. I use standart initialization:
static void peer_manager_init(void)
{
ble_gap_sec_params_t sec_param;
ret_code_t err_code;...
I've connected some sensors using I2C and SPI to a DK and their power consumption is not being reflected in the PPK. Without any BLE acitivity, the current is almost zero...
Hi,
I am using Ubuntu 16.04 (64-bits) OS.
I installed JLink_Linux_V620b_x86_64.deb and was using nRF5x-Command-Line-Tools_9_6_0_Linux-x86_64.tar
I can capture the...
