Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I am using jlink to program the custom board. I was able to program the board earlier, but now this error is comming. I have rechecked the connection and it is fine.
The...
Hello all,
I am in the design stage of custom board for Automotive application using nrf51824. i have the below queries,
In the below link there are two reference...
If the DCDC is enabled in the nRF52832 and during operation one or both the external inductors is damaged what is the effect on the device? Will the power sub-system compensate...
Hi,
I can send and receive commands from nRF51 Dongle to nRF51822 via using nRF Connect UART over BLE Service.
My question is : Is there another way to reach nRF51 Dongle...
Hello,
I have chip nrf51822 connected to nrf51dk. An usb connection provides power to both chips. While checking power of both chips via nrf connect on iphone7 i discovered...
Connect establish with smartfone in peripherial mode. SDK13. S132. Periodic I observe disconnect, than 2-3 advertise packet and new connect again.
Where can I see what reason...
I have a little hobby project going on where I'm trying to make Nordic's old temperature broadcaster example work with the nRF52: github.com/.../
The project was originally...
As the product specification says,The HFCLK clock controller provides mang kinds clock to the system:
HCLK64M:64MHZ CPU clock
PCLK1M:1MHZ peripheral clock
PCLK16M:16MHZ...
Hello Folks,
I am currently try to program RedBear BLE nano board (which is essentially nrf51822) using Nordic SDK v12, which has features of secure OTA. However after...
I have started working on the external file access with NRF
is it possible to read or access the data from the external file into NRF programming
similar to what we do...
I am running a modified version of the app_uart_c example on a nRF52832 using softdevice 132.
I want to send a large hex number to the peripheral I'm connected to. Is it...
Hi,
No matter what I adjust, I can't get the PPK to output over 2.2V. I happen to be using an older nRF52 preview DK (figured it'd be a good use for that board now that it...
tl;dr: UART transmission sometimes stops and never resumes. Only a
power cycle resolves the issue; a system reset is not sufficient. The
problem only occurs when flow control...
Hello,
as far as I have gathered, it is possible to use multiple peripherals on one device with the current alpha release of the S132 Softdevice. What I did not understand...
