I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Thats the problem.
On Windows7, 64 bit, with the Bluetooth Stack from the USB BLE-Stick happens the following:
Windows (master) initiates the connection, sends a security...
Hi, I'm using nrf51822 and using SDK12.3 ble_app_uart.
My purpose is sending data using BLE module like this:
Custom Board -> BLE Module -> Android Phone.
It works...
Hi,
I am using 2 nrf51822 devices. one is central and other one is peripheral. I am using s130 softdevice.
When i was trying to connect NRF51822 to other nrf51822.
i tried...
Hello All,
I am working on nrf52840 trying DFU OTA by following steps provided in this link github.com/.../ota-prog.md . where they have mentioned to install python all...
Hi Nordic,
I've used a GPIO of the NRF52832 to drive a FET circuit which latches off the battery, however as the board voltage collapses I see a short pulse on the GPIO...
In single bank mode, need upgrade bootloader by DFU. Performing below procedure, APK shows "transfer complete". Application on target device is disappeared, but bootloader...
Why does the nrf connect app on Android need my location services enabled for it to work? I believe that is the case for most (or all) of the nrf apps in Android.
Hello,
I am using nRF SDK 12.2.0 , with nRF52832 on pca10040 hardware, and working with the example in examples/peripheral/spi/main.c to develop a driver for LIS2DE12.
...
I've read as many posts regarding changing the ble connection interval as I can find but so far have been unsuccessful changing the ble connection interval.
Below has been...
Hi all,
Does in any chip with some constellation (different SD) the device allows less than 7.5ms for the connection interval? Or is this value the absolute minimum?
I am trying to connect to a peripheral device advertising f0000000-0114-4000-B000-000000000000 as the UUID. The peripheral adds it to the stack via sd_ble_uuid_vs_add after...
Hi,
I am using ESB in one of our current projects. I have two devices: one PTX (master) and one PRX (slave). The slave may want to send some data to the master from time...
We have an nRF52832 and an MSP430 on a custom board. We would like to program both the devices using SWD interface.
Would it be possible that both these devices can share...
Hi,
I have an nrf51822 ( variant AB) and I am trying to program a simple ble app beacon example on it.
But I am failing over and over. After searching , I found out that...
Hi,
I am using pca10040 board with s132 softdevice. I have integrated BLE_APP_UART service with BLE_APP_MULTIROLE_LESC example. The device will start advertising when command...
