I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
I am using sdk12.3 with NRF51822 and the original ANCS project. It can successfully bond with iPhone ,but the bonding only takes place at the first time after the firmware...
Hi, I am currently trying to receive a characteristic notification using an Android device which is connected to a ble beacon with the nRF52832 microcontroller. It works fine...
I am trying to pass data to a central device by updating a characteristic. I am calling the function sd_ble_gatts_hvx(m_bcs->conn_handle, &hvx_params) after passing a hvx_params...
NRF52 DK - SDK13.0 - ARMGCC - Eclipse
I am trying to add a custom service to the example ble_app_hrs.
I add all the part per the tutorial and end up getting error 7...
Hi.
I am working on a project which is using SPI and BLE together.
I wrote SPI code before without soft device. It has simple update function which is sending SPI data...
Hi
I did a bunch of boards for a product, and in the latest version I used a BQ25121 PMIC which also has a reset output which I tied to the nRF52 input. On the previous...
Hi all,
There are lots of posts on the devzone about adding DFU service to a custom application and they have been very helpful in getting to this point.
At this point...
I was looking into changing the S130 attribute table size, which is by default set to BLE_GATTS_ATTR_TAB_SIZE_DEFAULT, and noticed that this default seems to be set to zero...
Hi,
I have programmed my nRF52 DK using the ble_app_beacon example from SDK 14 along with S132 V5. I have set NON_CONNECTABLE_ADV_INTERVAL to 3000. I was expecting to see...
Greetings,
I am interfacing AT24C01A(EEPROM) with nRF52 ,SDK11,PCA10040.
For writing to the EEPROM and reading data fromn EEPROM, I am using the following code,
I have...
Hi, when reading the BLE Mesh example code, I got really bewildered by this function:
access_model_add
and inside, there is this gem:
element_has_model_id
...
What's the expected behavior when reading a register that is write only? For example, I'm using an some code that is reading the value of the TASK_START register of the RNG...
Will the Bluetooth low energy advertising tutorial run on 2 x nRF52 DK's and not on 1 x nRF52 DK and 1 x nRF51 Dongle? I wish to test the capabilities of BLE 5.0 (not be limited...
