I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Hello,
I purchased a nRF52DK to migrate my older projects running on nRF51822.
Version of the board is V.1.1.0 / 2016.19
I followed the 'Getting started' guide from...
Hello,
This is a DFU custom project...the core problem is that I cannot erase the bootloader settings page from the chip.
While trying to use a slightly modified version...
Hi
In current Desktop 2 project, We know that software device stack takes 48-bit random device address from FICR registers (DEVICEADDR[1: 0]) for BTLE. Each nRF51 has unigue...
Hello, I am devleoping a pc station using pc-ble-driver.
I was successfully able to install it on one of my computers but am facing a problem installing it on my surface...
The micro-ecc works well when I load micro_ecc_lib_nrf52.lib in keil5. However, the author suggest copying the uECC files into the project, so I include uEcc.h but fail in...
For the nRF51822, the documentation for ECB mentions it being used to
Encrypt/decrypt 16-byte data using
current key.
But it doesn't offer any methods to decrypt...
Hi,
Am using SDK 11.00 and NRF52 platform.
Am following below steps for dfu support.
1.Flashed Softdevice 2.00
2.Flashed dual bank ble Bootloader
3.Using nRFTool box...
Yan,
You mentioned these UART examples: examples\ble_peripheral\ble_app_uart or examples\ble_central\ble_app_uart_c I was not able to find them on your web site....
I have intention to use 52810's PWM output to drive motor. The timing requirement are critical so
hardware PWM is essential, rather than CPU generated waveform output.
...
Hi,
I am trying to increase MTU size for transfers and it works up to a size of about 72. After that I get an error.
Thanks to Sigurd I now know that it is when calling...
Hi, I've an application developed with SDK v8.0.0 and S110 v8, that is using the bootloader to start the main firmware and to start the DFU OTA (in case the user request to...
I currently have a problem with the gpiote setup. I'm using it to detect an interrupt from mma8652 accelerometer.
here is an annotated version with the key portions of...
Hi,
I've been trying to integrate the secure bootloader witrh SDK12 into my device, which had been working fine with the old bootloader and SDK11.
I've swapped everything...
Hello,
sd_softdevice_enable give me a hardfault every time. What can I do ?
Configuration:
Jlink / Ozone
Confirmed on 2 Sparkfun nRF52832 boards (nRF82832 AA rev 1...
