Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Currently using nordic52832 to develop products that use batteries.
We found that the problem is that when the BLE module is connected successfully, it takes 200ms to send...
Hi all!
I am developing an nRF52 application that uses RTC interrupt to measure an ADC value every 100 ms. Depending on the measured value the chip shall either go back...
I am using nRF 52 development board. Using Keil to program it. Its has 4 buttons. We can easily detect when a button is pressed, but is there a way to know for how much time...
I'm using the following code to make the beacon sleep:
static void on_ble_evt(ble_evt_t * p_ble_evt)
{
uint32_t err_code;
switch (p_ble_evt->header.evt_id)
{
case...
Hi, Developer Zone!
Can pm_peer_rank_highest function return NRF_ERROR_STORAGE_FULL code?
There is no this error code in description for function, but in the code I see...
Hi
I am sending my BT module with nRF51822 for some regulation test and the Test Lab is using Anritsu MT8852B to communicate with my module through USB-to-UART adaptor and...
Hi team,
I have seen the example of crypto in the SDK_12.3.0. I want to learnt it. But I don't know how to use it, because there is not keil project file, and I hadn't...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hello,
I have adapted the ble_app_uart_c project for a custom board based on nrf52832. The application already works fine, however, my peripheral is sending four packets...
Hi,
I decided to use nRFUART Example which is inside of the Master Emulator.
I am using nrf51 dongle for connecting peripheral devices.
When I run the nRFUART Example...
Hi,
I am porting my code from SR3 v1.0 to SR3 v1.1 now.
I have a problem in debugging SR3 v1.1.
In SR3 v1.0, it's fine in MDK-ARM debug session. I can set break point...
I have been working on integrating FDS into an SDK13 project using SES v3.24.
I'm not sure if the memory allocations are set correct. If I increase the FDS_VIRTUAL_PAGES...
So I have been integrating FDS into a project under SDK13. It's based on an example that Hung updated for SDK12.1. So after init of fds the method fds_test_find_and_delete...
This crystal, which is used the nRF52 dev boards and reference designs, is now "not recommended for new designs". I could find another crystal that meets the spec, but just...
Hi,
i'm currently try to figure out how to use an Android device as an IPv6 Server through BLe sending UDP packages. One of my collegues tried this example as it was discribed...
