Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hi,
nRF24L01 seems like a perfect choice for home automation project that I have in mind .. I will have to install about 20 of those around the house.
My question is...
Hello,
I'm working on the bootloader using SDK13.1. In the file dfu_req_handling.c there is a variable called m_flash_operations_pending that gets incremented with every...
HI,
I am very new to this, I am looking to put a video or flash player or another image to to load into my nRF51822 beacon kit. I am thinking the straightaway method would...
Hi,
I am working with ble_app_uart code, in that I am trying to configure different baud rates like 9600,38400 and 57600. With these baud rates I am not getting any issues...
Hi
sd_ble_gattc_primary_services_discover() is being called from ble_db_discovery_start() within ble_db_discovery.c. I'm trying to get the ble_cts_c service working. It...
Hi
I am receiving INVALID_STATE (error code 8) from ble_db_discovery_start. According to documentation, this error can be returned "If this function is called without calling...
Hi, i have just bought a NRF51 DK. I have tried to run the precompiled Blinky example. I have first installed NRFGo Studio. I connected the board. In NRFGo Studio, I selected...
Hello,
I am making a battery service to report the battery that is sampled by the SAADC, so far I am am able to compile it and debug it, however I see how my saadc_event_handler_interrupt...
Hi
I'm reading the debug output of ble_cts_c.c:
NRF_LOG_DEBUG("BLE event handler called with event 0x%x\r\n", p_ble_evt->header.evt_id);
However I can't find any...
The analog circuits 51822 and rfx2411n supplied by the authorities are connected 52832, but the circuit is not working properly.PA and LNA switching has been controlled in...
This is to build upon a previous question i had here .
This time, I am having issues with SDK 14.
I can compile and run the BLE peripheral HRS example fine. With SDK 14...
Hi,
I am trying to write 64 bytes to a characteristic as a client and am getting the error NRF_ERROR_DATA_SIZE . The infocenter is not very helpful at indicating where...
I am using S132V3 on NRF52832 device. In my application we need to set a static, non-rotating, private resolvable address. I can't get into why that is here. In theory this...
Hi all,
I'm using chip nrf52832 with the last enabled stack which integrates the adaptive upgrade for bluetooth 5.0. However I'm insterested in long range and that's upgrade...
Hello,
Is there any example of simple peripheral to update the firmware using over the air download for nrf51?
waiting for your kind rhelp.
Regards
MAbbas
