i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hello
I want to change the mac address of my device from normal mode to random mode,
I do not know how this does for nrf52832 (NRF52-dk)
Thank you in advance for your...
Hi All,
I've got a nRF51-DK development kit, and I just compiled and downloaded my first example to it through Keil uVision. Problem is that nothing happens when the program...
Would it be advisable for system design to use CAN(CAN Open) and BT simultaneously on nRF52832 IC?
Why this bothers me is because capabilities of nRF BT MCU's are growing...
Is it possible to limit the connection duration on BLE peripheral (nrf52832)? For example, if central is in connection for more than X seconds, then peripheral terminates...
hello everyone,in my code, SDK9.0 uart ,please tell me the reson if you the book of knowledge
static void timers_init(void)
{
uint32_t err_code;
APP_TIMER_INIT...
I am looking at the att_mtu_throughput example in the blog ( devzone.nordicsemi.com/.../)
Some of the items in configuration menu that are shown in video and listed in...
Hi,
I am using sdk13 with a nrf52832 dev kit.
I have two separate projects one with a bootloader and other with an application.
I use the following configuration in the...
Hello,
I am using nRF51822 and an STM32 communicating over UART. I want to test UART communication without CTS and RTS so I did the configuration as shown below:
static...
I've been using the NRF24L01 transceiver to wirelessly broadcast data back and forth among 4 devices, where each device contains the NRF24L01 chip. Everything works great...
Hi, I'm using nrf51822 and ble_app_uart(SDK 12.3.0)
What I want to do is connect my board with nrf51822 and send data over UART
and send data to smartphone over BLE...
When I used keil, I set breakpoints to debug ble project used softdevice. And it was useful..
And now I'm using eclipse and gcc. It works well at first, but when step debugging...
Im using nRF 52 DK. I need to use BLE and ANT simultaneously, but the problem is most of the SDK v12,v13 examples use softdevice s212 for ANT,which does not support BLE examples...
Hello , i'm trying to implement the OTA DFU function in my custom designed board. I'm using NRF52 series. I started by flashing the flash I uploaded the softdevice132 v2 via...
I have a few nrf51822 modules powered up but why do they all have a uuid of 0x1234?
They are programmed for UART services (they just spit the data from an android app when...
