Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
In my nRF52832 base-board, I don't have any leds and buttons.
I use Keil v5 and I used ble_app_uart_pca10040_s132.
I copied pca10040.h as custom_board.h and replaced BOARD_PCA10040...
I Cant clear the RTC2 after a Compare Match. First Compare is Triggered. After that no more Interrupt is generated. Code:
static const nrf_drv_rtc_t rtc = NRF_DRV_RTC_INSTANCE...
I debugged with pca10028, but J-Link can not recognize manufacturer.
If selected cortex-M0, it works but is very inconvenient.
How can I solve this problem?
Hello,
i am meeting problem to program the SoftDevice using an example project in Keil for nrf52832.
i have tested the development kit setup use Blinky Example . it is...
Hi,
We are using sdk12.3.0 sd130 v2 on nRF51822(32KRAM version). We want one central to connect to at least 3 peripherals. We are starting with ble_app_hrs example at the...
Configuration:
nRF5_SDK_13.0.0_04a0bfd
PCA10040
ARMGCC
Background:
I have created custom service based on ble_nus service. I have created 4 characteristics with notify...
I'm concerned about users writing too much or invalid NDEF data to the NFC function.
This could result in parse errors or buffer overflows leading to system crashes/malfunction...
Good Morning,
I need help for integrating a wifi card of this type or another that may suggest. With explanation of connection in the pinp Gpio of the thingy52 board, what...
Hello everyone,
I am looking to start developing something using nfc but I am unable to do so.
I am using SDK v12 and it has nfc examples as well like "record_url" or "adafruit...
Hi,
How to integrate both over-the-air and uart bootloader application for an device? We have a custom board with nrf51822 chipset, and we need to implement the firmware...
Hello,
I'm currently experimenting with the dual-bank bootloader in SDK 13.1. According to the documentation, if the new application can be activated, it is copied from...
Hello everyone,
I'm developing a new device using the nRF52832 but I have 2 questions before I send my PCB to manufacture, I hope you can help me out:
Is there any...
Hi,
Congratulations on releasing nRF Connect v2.0!
Unfortunately, I'm having trouble with adding apps behind corporate SSL proxy. Is there a workaround for this?
Please...
Hi,
I am trying to change the uart example using NRF 52 with SDK 12.3, so that I would hold a button pressed and it would send the time of button being pressed after release...
