I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I have some question about ANCS ,when we trun off the IPhone and turn on the IPHONE.
The notifcation is disabled. I have to turn OFF the bluetooth and ON bluetooth form ISO...
Hi All,
I am a beginner,Can you please explain me what is the role of this line?
APP_ERROR_CHECK(nrf_drv_spi_transfer(&spi, m_tx_buf, m_length, m_rx_buf, m_length))...
Hi All,
I am using nrf51422, SDK 12.0.0, an SPI OLED display 128x32, and an SD card.
I want to interface an OLED display and an SD card onto the nrf51422. Although my...
Hi all,
I like build a smartwatch-like device that can receive notifications from my android phone. The bluetooth device has a oled screen and displays what notification...
I need to turn on and off one pin around every 100 us. Time between must be 1 cycle (couple of ns) and can't be interrupted at any circumstances.
Without a softdevice I disable...
Hi All,
I am a beginner in nrf52.
I need to get the client device address in ble_app_hrs_central, because I have more than one devices connected.
There is a hrs_c_evt_handler...
After spending half a day on this solution, I found out it wasn't really a solution - it devolved back to the same issue after trying to connect - please advise!
Description...
I'm trying to connect to a ST LSM6DS3 via SPI on the Nordic chip. I have used SPI on Nordic with other peripherals but couldn't seem to get it to work with this ST chip. Eventually...
I'm having some issues getting any of the provided experimental Thread examples to compile with IAR version 8.11.2. I'm using an nRF52840-PDK with the SDK for Thread version...
Hello,
I wonder how power failure comparator works at VDD 2.1V.
If VDD goes down to 2.1V, and I set POFCON enabled at 2.1V threshold, then does POFWARN work?
How 2.1V...
Hi,
I am working on testing this modification on the ble_hrs example.
The idea is to send data sequentially as notifications.
However, BLE_EVT_TX_COMPLETE seems to...
Good morning
I use the fds function to store and read data in flash memory.
FDS_SUCCES is not returned by the fds_record_find function when reading data, so the read function...
Currently developing on NRF52 sdk12
I want to be able to show time stamp minutes:seconds:miliseconds on my RTT viewer, when I print my data out from the uC. Any hits on...
hello
i am using nrf52840, with BME280, i have external pullup 10k resistor.
how i can disable the internal pullup resistor.
i am using this sample code.
github.com...
