Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello, long story short:
You now must use write request instead of write to write the CCCD descriptor.
Allegedly (according to a nordic employee) both types...
Hello,
We are currently designing the hardware for a production run of our product using the nrf52832 chip and would still like to have debugging capabilities with breakpoints...
I'm using an NRF51822 with soft device s110 version 7.1.0 and I'm having timer-related issues.
I create 1 periodic timer and 6 non-periodic (single shot) timers with app_timer_create...
Hello guys,
Hope someone can help me here. I am working with the NRF52 and want to use Zephyr . I am able to flash it. Using the nrf52 as periphal does not cause problems...
Hi,
I'm using SDK13.
I'm tring to save big size data (about 10KB) into flash when received them with 20 bytes pieces.
I called fds_record_write() in NUS's data handler...
Hi, I'm new to wireshark, and I want to filter all those empty pdus, they make it really hard for me to find the useful packets.
I tried btle.lendgth != 0, but got an error...
So I'm basing this off of the ble_app_hrs that initially has heart rates service and battery service. I want to create my own custom service andcopied the project to use as...
Hello,
I tested the example project "custom serial chat" from Atmel and wanted to see which Handle is used to send and receive data from Smartphone to the BLE-Board (SAMD21...
Hi.
I am designing PCB based on NRF51822-QFAA-R7.
There is 2450BM14E0003T balun will be used.
Here is reference design for that pair (NRF51822 + 2450BM14E0003T):
www...
I would like to register a bug report with the nRF5 SDK version 12.2.0. If you look at the example code in the SDK you will find that every example has a different build configuration...
We have a project which need to control the distance between the slave and the master to be less than 10m, say 5m. We tried -20 and found it a little longer than we expected...
How can I trasfer 20bytes data per 10ms?
Currently, I set gap_conn_params.min_conn_interval 7.5ms, and use BLE_EVT_TX_COMPLETE to send data. However, Android APP nrf Connect...
[Aim]
I am working on a project where I aimed to Integrate/Develop firmware management system using Contiki running over Nordic NRF52.
[Components]
Contiki running over...
