Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
I guess my question is stupid, but I would like to ask it by the way..
in all ble examples we use a function for handling ble events by our app
in my case in example ble_app_uart...
I'm trying to launch my app on a custom board with nrf52 after a successful launching on DK. The problem is here: err_code = sd_softdevice_enable(p_clock_lf_cfg, softdevice_fault_handler...
Hi folks, I'm making progress with a program to get two nRF24L01p modules communicating with each other, but there are a couple of remaining problems. I hope someone can help...
I have a little bit of experience on TI BLE stack development and wanted to move to Nordic product with Bluetooth or ANT protocol for a higher data rate. I got a general question...
Hi All,
I have a problem with .hex file. I use example ble_app_uart from nRF5_SDK.
In examples\ble_peripheral\ble_app_uart\pca10056\s140\armgcc I executed: make all and...
I try to turn off the system with sd_power_system_off()
// Go to system-off mode (this function will not return; wakeup will cause a reset).
err_code = sd_power_system_off...
Based on 'ble_app_template' in nRF5_SDK_12.2.0 (S132), I develop a program with nRF52832.
The problem is that the program will restart after reaching APP_ADV_TIMEOUT_IN_SECONDS...
Hi,
I have a few questions about using floating point in nRF5 chips. As discussed here , nRF51 has no FPU but we can simply use "float" in Keil and have the operations...
My device as a slave, if the surrounding environment is not good, the unknown master device connected to my slave device caused the real master device to be unable to scan...
Dear Nordic family,
I tried programming MDBT40 (purchased from Raytac ) with the same code which worked with nRF51822 Bluetooth Low Energy BLE 4 and 2.4GHz Wireless Communication...
I'm trying to implement a simple RTC timer into my project, and it seems like the app_timer module is the best way to do that, especially when using the Softdevice. I added...
Hello,
we are facing the following issue when using Android and trying to rebond with a previously bonded S110 peripheral:
Bonding the Android device with the S110 based...
We are looking to store a unique name and number in each device as it is provisioned from the factory, and are considering using the UICR. We are using something close to...
