Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
Hello.
I want RSSI check. so added source code as below.
test_rssi_start = sd_ble_gap_rssi_start(m_conn_handle,BLE_GAP_RSSI_THRESHOLD_INVALID,0x00);
if(test_rssi_start...
Hi all,
Is possible using NFC to send variable message? I want to send a counter event (data I got via BLE) to the NFC module.
Using the example I was not able to do...
Hey,
I'm just wondering how to add a UUID to the blinky example peripheral?
I want something like the heart rate sensor where its advertising BLE_Heart_rate_sensor.
I...
We have recently migrated from a custom board based on the nrf51 to a new board with the nrf52832. Our nrf51 board used to run at 6-8 uA when it was just sitting there advertising...
Hi
During schematic design, i read regarding proper powering of NRF52 (the product is battery powered 2xAAA). somehow i can't find this info now and i would like to verify...
What does mask and 1<< mean in the following code:
#define BSP_LED_0_MASK (1<<BSP_LED_0)
#define BSP_LED_1_MASK (1<<BSP_LED_1)
#define BSP_LED_2_MASK (1<<BSP_LED_2)
...
Hi all,
I'm transferring data to and from an Atmel AT25040 NVRAM using SPI, and it works perfectly when run within main(). However, if I run the same code from within an...
Hi, I want to enable notification for a specific characteristic, and to do that, I must write 0x01 (in java it's going to be "01,00" ) to the CCCD handle of this characteristic...
Hi,
I tried to use python API to drive the nrf sniffer to capture ble device information by their advertisement packet. I can successfully target a specific ble device...
Hi, I'm wondering how much i need the LF crystal oscillator.
In this case, the chip is never asleep, in constant latency mode, and is constantly advertising and meshing...
Hey guys,
We have several different devices that use the nRF51822 and some using the nRF24L01. We currently use the proprietary RF protocol and have all of our devices successfully...
Hi,
Reading from flash, an already programmed key, returns zero.
Using sdk 12.1, sd s132_nrf52_3.0.0, nrf52832, and pstorage. The key is programmed after uploading the...
On nRF52 interrupts for GPIOTE, I need to perform one event when a button is pushed, and perform another different event when the button is released.
I've checked these...
