Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
When I try to write a UUID into the UICR registers using the method described at - Software Development Kit > nRF5 SDK > nRF5 SDK v12.2.0 > Examples > Hardware peripheral...
Hi Team,
I´am working with the nRF51422 and would like to change the parity from even to odd.
Is there any possibility to change that setting or just to invert the even...
Hello,
Is there any possibility to configure the UART parity to odd on chip?
I am using the nRF51822 chip. I could activate the parity but inside the documentation they...
Hello
I am building bootloader. I do not use Softdevice and used example from this topic . Bootloader must read FW from uSD card, update flash and jump to application....
I am using nrf52 , it's always connected to an iPhone, and I need a truly real time respond.
I am sending short messages, like 2 characters at a time, and play a sound on...
Hello, I'm using the nrf52840 SoC, and nrf52840.h appears to be a more "localized" and "specialized" version of nrf52.h for nrf52840. So quite reasonably I should use nrf52840...
Hello, my harddrive went awry and some part of it were damaged (I assume it was file table because a lot of files are affected simultaneously).
So for the past few months...
In s130v2 SDK12.3.0, ble_uart_c, I have set BLE_DB_DISCOVERY_MAX_SRV to 12. Also memory linker is: IROM1: 0x1B000 size: 0x25000. IRAM1: 0x20001EB0 size: 0xBFC0. I use nrf51822xxaa...
Hi,
I have an application where first nrf51822 would act as central, a second nrf51822 would act as peripheral, a third nrf51822 would act as a peripheral. I found that a...
I have the opportunity to select the voltage of the power supply feeding an nRF52. There no other chips in the system, thus there are no other constraints on the voltage....
I want to sign a block of data from my nrf51822. I though the cryptographic library would serve my purpose. But I am not quite able to get my code working. I tried searching...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hi,
I have an application, where I need to send beacons and listen to beacons. Is it possible to do both in the same code base, without tearing down the softdevice and re...
Hi,
I would like first nRF51822(device 1) to use Gazelle library to talk with another nRF51822(device 2) and the same first nRF51822 to use Bluetooth to connect to another...
Hello,
i'm currently looking into ble-bcast-mesh with the goal to transfer a large amount of data (up to 1kB) from one node to another. ble-bast-mesh is working (as far...
