I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
Howdy!
I have to admit that after about 2 weekes of fight i finally made some progress with NRF51. Afterall i can upload my own program to chip so it changes leds on NRF51...
I get an error when trying to pair to a peripheral in nRF connect v1.0 on Linux.
I have two nRF-DK v1.1.0 (pca10040), one is the adapter that is connected to nRF Connect...
After flashing softdevice, the ble_advertising_evt_handler_t doesn't get called, only after flashing the program for the 4th time.
/**@brief Function for initializing advertising...
When I connect the nordic ID stix to my android tablet using the micro-USB to USB cable, the nordic ID stix doesn't appear green light on it. Is it need to install any driver...
I would like to dynamically change bluetooth LE advertising interval. I am using nRF51 and nRF52, with SDK's 8 and 12. Is that possible and how to do it?
Our application...
Good day everyone,
I would like to utilise the nRF52832 BLE chip in an application that requires radio communication between a master and slave. The slave needs to be powered...
Hi everyone,
I am using LPCOMP in rFF58122.
When coosing the reference voltage, I have to fill the structure nrf_drv_lpcomp_config_t with the hal nrf_lpcomp_config_t that...
Hello, I try to add TWI function in my project (uVision5) so I add this modules with 'Manage Run-time Environement':
nrf_drv_twi
nrf_twi
app_twi
and I get...
hi
I have a problem in integrating a 1.8V GSM modem with nRF52832 through UART. nRF52832 supplied with 3.3V and there is a voltage divider that covert 3.3V to 1.8V in the...
hello....
Nrf 52832 does not work.
With a newly developed board,
Programming with nrfgo studio and J-link is not possible.
It feels like it does not have a good reset...
I'm looking for an example code of central role which can run on nRF52 DK.
I want to check if it is possible for nRF52 DK to send a LL_CONNECTION_UPDATE_REQ PDU to slave...
In general, I'm working on my own dfu-bootloader project which was developped on the "Engineering A" chip-revision of the nRF52832. We finally have new hardware with the chip...
Hi all,
I have use nRF5_SDK_11.0.0_89a8197 and S130 before and use nRF Toolbox to do switch it to bootloader and do OTA, just use one APP. However, now I'm using nRF5_SDK_12...
Hi,
I look at this demo,found that the ESB is PRX in most time, it may lead to a high power consumption.I want to achieve auto ack, piggybacking data in ACk from PRX.So the...
Hi all, I'm working on experimental_ble_app_buttonless_dfu project in sdk13-alpha using pca10040 board. I just compiled experimental_ble_app_buttonless_dfu successfully for...
